KUDI230B0 KitchenAid Dishwasher - Instructions

Disasembled pump to find dammaged parts replaced with new parts . Made wife very happy .

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

I followed advice already posted and applied some liquid soap inside each end of the tube. Perfect!

Used duct tape to hold the old tube in place until I had a chance to see if the part was available online. Found it, ordered & received it the very next day. (Great service!) Removed the old tube which was already half off once I removed the duct tape & slipped the new tube on. A little trouble at the rounded end, but I used a screwdriver handle to kind of mold that end round & then slipped on.

This repair was just so easy. I am a 65 year widow and did not want to call repair for something that I thought I could do-ordered the part and it was delivered in two days. I rubbed a small amount of vaseline around both the tube's ends, used the hair dryer to heat slightly, attached one end of the tube to the upper spray arm receiver and the other end to upper wash assembly and job completed. My savings was probably $65.00 or more for no service call. Works great and dishes are clean again.

Piece of cake --after having read what others had suggested on your webpage, I used the heat from a hair dryer which made the piece pliable and simple to fit into place. It took less than five minutes. When my husband came in from work, I proudly told him the part had arrived and it was fixed! Taa Daa!

I took the first bumper, I had bought two, and tried to snap in on to the rack. It was too rigid and broke.

My son heated the second one in hot water and it snapped right on.

At least I know the secret to installation, but now I need another bumper.

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

I am a 73 year old lady. My nephew found the torn rubber water delivery tube after a repairman had found nothing. I looked up the model number, contacted Part Select by e-mail, ordered the part ($15.++ for cost and delivery), read reviews and found tipe for installation. Total time spent on installation was less than ten minutes. The round tube, with a smidgen of liquid detergent inside each end of the tube, fits onto the water line; the other end of the tube will squeeze flat with little effort, and fits onto the apray arm.

I bought the kit because it had other parts that I thought I needed.

I just pulled out the rack and removed the eight existing roller wheels and roller axles. I was able to remove most of the roller axles with my fingers but needed pliers to remove a couple of them. I then snapped the new roller axles onto the rack and then the roller wheels onto the new roller axles and put the entire rack back in the dishwasher.
The lower rack now rolls smoothly and consistently no matter how many dishes we have piled into it. Also, it has not come off the tracks since replacing the roller axles and roller wheels.

Snapped in new ones (8) by hand. I was amazed
how fast I was able to find this part online and the
ordering was easy and in a few days the parts
arrived. No hassle trying to explain to anyone what
part I needed. There were pictures of all parts
available. Ordering online, especially if you
know what you are looking for, is really the way to go.

The whole operation took about 5 minutes which included opening the package! Sprayed some vegetable spray inside the opening of the water tube that attached to the spray connection and it slipped right on. Absolutely amazing and I feel like I have a brand new dishwater! My dishes are definitely cleaner too! Thank you Parts Select for posting how to instructions!