Models > KUDC10FXSS5 > Symptoms > Leaking

Parts That Fix KitchenAid Dishwasher KUDC10FXSS5 Leaking

Leaking is a commonly reported symptom for the KUDC10FXSS5 KitchenAid Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your KUDC10FXSS5 KitchenAid Dishwasher that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Leaking is a commonly reported symptom for the KUDC10FXSS5 KitchenAid Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your KUDC10FXSS5 KitchenAid Dishwasher that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 25% of time
★★★★★
★★★★★
2 Reviews

Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.

$ 46.83
  In Stock
PartSelect Number PS12348515
Manufacturer Part Number W11177741

Replacing your KitchenAid Dishwasher Dishwasher Door Seal

Replacing your Dishwasher Door Seal

Customer Repair Stories

leaking from door
Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.
  • charles from MAURICE, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking gasket
Easily pulled old gasket from channel. Soaked new gasket in warm water. Cleaned debris from channel with wire brush and CLR. Starting at top-middle, gently pressed new gasket in place. Used a gentle push-pull technique on the corners. Used fingers to smooth gasket all around. Closed door and kept latched for 2 hours. Ran dishwaher to check for leaks.
  • Larry from BENICIA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
66 of 76 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Seal
Fixes Symptom 17% of time
★★★★★
★★★★★
3 Reviews

This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The door seal is designed to seal the gap between the dishwasher tub and outer edge of the door. This helps to prevent leaks when your dishwasher is running. A leaking dishwasher is a good indication that the door seal is damaged. This seal is sold individually and is an OEM part sourced directly from the manufacturer.

$ 9.89
  In Stock
PartSelect Number PS11755651
Manufacturer Part Number WPW10497235

Replacing your KitchenAid Dishwasher Seal

Replacing your Seal

Customer Repair Stories

door leaks bottom right
leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.

THANKS,
PETE GODSHALK
  • Peter from LEBANON, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door leaking from corner.
First, I replaced the bottom door seal. You will need magnetic nut drivers because of the location of the 3/16 screws that hold the seal in place. you also need a 1/4 in nut driver to remove plastic cover that covers up the 5 3/16 screws. Last you need a small star driver to remove the door screws. Note 4 of the door screws, the 4 on top of the door are much longer than the side screws. With all this said, this seal was not my problem. I then replaced the large black rubber seal around the tub. Be sure if you do this you fold the seal in half and start in the middle of the top of the opening so you have the exact amount of seal left over on both sides. Also when you remove the old seal, clean the area it was removed from with a damp cloth. Turns out, That was not my problem either. So now I will move to the next step to see where the water is coming from but maybe this information will help someone with a simple door leak.
  • Don from GRAPEVINE, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
42 of 47 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 Seal
Fixes Symptom 11% of time

This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping during a wash cycle. If your dishwasher is leaking you will need to replace the seal, as it is likely damaged. The first step should be to check the seal for buildup of food particles near the sides and the bottom of your appliance.

$ 76.91
  In Stock
PartSelect Number PS11731683
Manufacturer Part Number W10864081

Replacing your KitchenAid Dishwasher Seal

Replacing your Seal

Customer Repair Stories

Leak
1. Remove old seal
2. Install new seal
  • Charles from WALLBACK, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking door seal
Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.
  • Charles from ELGIN, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 6% of time
★★★★★
★★★★★
3 Reviews

This drain hose is 6 and 1/2 feet.

$ 31.57
  In Stock
PartSelect Number PS2358130
Manufacturer Part Number 8269144A

Replacing your Kenmore Dishwasher Drain Hose

Replacing your Drain Hose

Customer Repair Stories

Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
  • Robert from Beaufort, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unwanted water.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
  • David from PITTSBURGH, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 5% of time
★★★★★
★★★★★
6 Reviews

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

$ 74.53
  In Stock
PartSelect Number PS11752927
Manufacturer Part Number WPW10327249

Replacing your Whirlpool Dishwasher Water Inlet Valve

Replacing your Water Inlet Valve

Customer Repair Stories

No water was entering the dishwasher.
Disconnected the water hose entering and one electrical plug alone with one screw that holds the valve to the machine. Replaced the old with the new and it worked.
  • Joseph from WAKE FOREST, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High pitched noise when the washer filled at the beginning of the cycle.
Watched the video, it went as advertised. Easy repair and the noise is gone.
  • Robert from E GRAND FORKS, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 5% of time

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

$ 11.77
  In Stock
PartSelect Number PS11743008
Manufacturer Part Number WP596669

Replacing your Kenmore Washer Hose Clamp

Replacing your Hose Clamp
Fixes Symptom 4% of time
★★★★★
★★★★★
1 Review

This fill hose is a genuine OEM replacement part for your dishwasher. The hose is made of black plastic, and is accordion-style, for ease of movement within your dishwasher. To replace the fill hose, you will need a 1/4 inch nut driver, Channellock pliers, and a Phillips screwdriver. Replacing this part will require some disassembly, such as removing the water inlet valve from the fill hose, and the clamps which secure the hose in place. Reuse your existing clamps when securing your new fill hose in place.

$ 77.20
  In Stock
PartSelect Number PS11738178
Manufacturer Part Number W10878507

Replacing your Whirlpool Dishwasher Inlet Fill Hose

Replacing your Inlet Fill Hose

Customer Repair Stories

The hose had a slit in it.
I removed old hose and replaced it with a new one and reinstalled the dishwasher.
  • Larry from Sarasota, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Hole in filler hose
twist filler hose assembly to the side and slide hose in. place clamps on hose and attach to water supply and valve.
  • Gordon from Davidsonville, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 4% of time
★★★★★
★★★★★
5 Reviews

This part is used to drain water from your dishwasher.

$ 48.17
  In Stock
PartSelect Number PS11756139
Manufacturer Part Number WPW10545278

Replacing your Whirlpool Dishwasher Drain Hose

Replacing your Drain Hose
Fixes Symptom 3% of time

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

$ 11.09
  In Stock
PartSelect Number PS11740613
Manufacturer Part Number WP285655

Replacing your Kenmore Washer Hose Clamp

Replacing your Hose Clamp
Fixes Symptom 3% of time
★★★★★
★★★★★
2 Reviews

This is the replacement impeller kit for your dishwasher. This impeller kit comes with 4 pieces, including the impeller and seals which you will need for the repair. The impeller and seal kit is mounted on the dishwasher motor. If your dishwasher is not cleaning dishes properly, it may be an indication that your impeller has gone bad, and you are not getting proper water pressure. If the seals have gone bad, your dishwasher may start to leak. If you are having either of these problems, you may need to replace the impeller kit. Be sure to disconnect the water and power source from the dishwasher before you begin this repair. This is an OEM part sourced directly from the manufacturer.

$ 94.42
  In Stock
PartSelect Number PS12069388
Manufacturer Part Number 8193951A

Replacing your KitchenAid Dishwasher Impeller

Replacing your Impeller

Customer Repair Stories

The ceramic seal had failed, allowing water to destroy the front motor bearing.
Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.
  • Jerome from Greensburg, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
19 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishes would not clean
Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.
  • Kathryn from Gordon, NE
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
37 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time

This part is also known as a float switch. This float switch, when activated, stops the flow of water into the dishwasher.

$ 47.54
  In Stock
PartSelect Number PS11750031
Manufacturer Part Number WPW10195039

Replacing your Whirlpool Dishwasher Overfill Control Switch

Replacing your Overfill Control Switch

Customer Repair Stories

DISHWASHER WOULD NOT FILL WITH WATER
Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.
  • TRACEY ANN from BRICK, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
  • Dennis from AUBURNDALE, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
12 Gasket
Fixes Symptom 2% of time
★★★★★
★★★★★
2 Reviews

Also known as a washer.

$ 42.46
  In Stock
PartSelect Number PS11746142
Manufacturer Part Number WP8531743

Replacing your KitchenAid Dishwasher Gasket

Replacing your Gasket
Fixes Symptom 1% of time

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

$ 7.75
  In Stock
PartSelect Number PS11743934
Manufacturer Part Number WP717273

Replacing your Whirlpool Dishwasher Rubber Washer

Replacing your Rubber Washer

Customer Repair Stories

Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
  • Jose from HOUSTON, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishes would'nt come clean or dry from torn boot
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
  • David from Sallisaw, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
14 VOLUTE
Fixes Symptom 1% of time

This part forces the water from the pump to the sump area for discharge.

$ 10.65
  In Stock
PartSelect Number PS16745117
Manufacturer Part Number W11622922

Replacing your KitchenAid Dishwasher VOLUTE

Replacing your VOLUTE
15 Float
Fixes Symptom 1% of time

$ 63.60
  In Stock
PartSelect Number PS11750028
Manufacturer Part Number WPW10195036
Fixes Symptom 1% of time
★★★★★
★★★★★
5 Reviews

The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.

$ 222.31
  In Stock
PartSelect Number PS11757388
Manufacturer Part Number WPW10757217

Replacing your KitchenAid Dishwasher Circulation Pump and Motor

Replacing your Circulation Pump and Motor

Customer Repair Stories

Dishwasher motor - making a very loud grinding noise
I went on the internet and found a pdf file with the Kitchenaid dishwasher repair manual for my model. One of the hardest parts of the job was convincing myself that I could do the job. When you're young, you just go out and buy a new dishwasher and tell yourself, "it's only money, we'll make more." When you're over 50, you tell yourself, "I can fix this. It will mean I get to retire a week sooner if I don't spend another $700 for a new dishwasher."

In hindsight, I could have done this job (replace the motor) in about 30 minutes. 1) Turn off electrical breaker in basement. 2) slide out dishwasher. 3) disconnect water supply. 4) use old towels to soak up any water still in the tub. 5) turn dishwasher on it's side. 6) unhook the wire harness plug from the motor, squeeze with fingers to unhook. 7) unbolt motor, 1 bolt. 8) turn motor counterclockwise, 1/4 turn. 9) pull motor out from sump, requires some force. 10) install new motor, but use some rinse aid to lubricate the rubber seal on it. Instead I did things the hard way and took the whole darn machine apart!!! See my story below.

I was surprised at how simple the design was and how few parts there really were inside the dishwasher. I found the pdf repair manual very useful, and I also found some repair videos on line. One thing they may or may not tell you - clean the parts well and lubricate the gaskets with some 'rinse aid' liquid when you put the machine back together. Also, it might help you to take a few pictures with a digital camera before you take things apart - that might help you remember how things go back together. Take close up pictures and use a treble light to illuminate the area when you're taking a picture.

The new motor was the ticket to fixing the loud noise. I was worried because the part cost $150. Before I ordered a new motor, I hooked up the old motor to electricity on my work bench and was able to recreate the really loud noise - so I was pretty sure that the new motor would eliminate the problem. It was very easy to install the new motor, only one bolt holds it in place. I did need to disassemble several parts to get to it though. Have no fear. One thing I did was mark the electric leads that went to the small pump with red and black sharpie markers so I could easily see which terminals to plug them back onto.

After reassembling the whole dishwasher with a new motor and testing the dishwasher for leaks by pouring a couple pitchers of water into it - I put the beast back under the counter (hooking it back up to the water supply line, the drain pipe to the garbage disposal and finally the electric supply). Then I ran it and water gushed out the bottom.

This whole job should have been easy, but things never go easy for me. Maybe if I would have lubricated the old sump gasket with rinse aid it would have sealed properly when I reinstalled it. Maybe if I would have cleaned the old sump gasket and the bottom of the tub really thoroughly things would have sealed right. But I didn't - so it leaked. I went ahead and bought a new sump gasket ($30 and had a few more days of waiting and self-doubt and having the dishwasher broken down). One the gasket came, I went through the entire uninstall, disassembly, reassembly and reinstall process AGAIN!!! This time with the new clean sump gasket and thoroughly cleaned surfaces. I also lubricated the gasket with rinse aid before installation. NO LEAKS! Job finished. Lessons learned. Doing it the first time was pretty tough though. Good luck! Get a helper for moral support and picture taking!
  • Michael from St. Louis, MO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
148 of 153 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
  • Steve from Inver Grove Heights, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
221 of 249 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
5 Reviews

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

$ 72.39
  In Stock
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269

Replacing your Whirlpool Dishwasher Dishwasher Drain Pump

Replacing your Dishwasher Drain Pump

Customer Repair Stories

Dishwasher not draining
This was one of the easiest jobs I ever did first I rremoved the excess water with a Shop-Vac then removed the kick plate two screws then removed the clamp from the drain hose pulled the electrical wiring off the pump removed the pump by turning it counterclockwise put the new pump in turning it clockwise it took less than a half-hour but a little more than 15 minutes
  • WILLIAM from MCKEES ROCKS, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
15 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
  • Andrew from Alexandria, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
481 of 537 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
18 Gasket
Fixes Symptom 1% of time

Used with the water inlet valve.

$ 34.79
  In Stock
PartSelect Number PS11746138
Manufacturer Part Number WP8531323
Fixes Symptom 1% of time

This is a flexible drain hose that is 12 feet long.

$ 28.77
  In Stock
PartSelect Number PS970496
Manufacturer Part Number 3385556

Replacing your Whirlpool Dishwasher Drain Hose

Replacing your Drain Hose

Customer Repair Stories

Installing a new dishwasher in a remodeled Kitchen
I remodeled my kitchen with new cabinets. In order to better utilize cabinet space, I located the dishwasher away from the sink, which means that I had to have a longer drain hose. The store I purchased the dishwasher from didn't have a longer hose, so I went online and found it on this website. Thanks for the quick shipment. I ordered it using standard delivery and received it in less than three days. I have book marked this website for future use.
  • Maxie from Bridge City, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time

Also known as a wash arm seal.

$ 5.41
  In Stock
PartSelect Number PS11745436
Manufacturer Part Number WP8268340

Replacing your KitchenAid Dishwasher Spray Arm Seal

Replacing your Spray Arm Seal

Customer Repair Stories

PartSelect screwed up.
Couldn't do the repair because you people sent the wrong part.
I ordered #1174536, spray arm seal, but got #wp8268340, bearing.
Waiting for you to make this right.
Please feel free to publish this. Tom Hanna
  • Thomas from BLOOMFIELD, MI
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing order
I wish I could describe how my repair went! My order was shipped on August 27 (per: the company's email ). However, I have not received our part, yet and it is September 11! I contacted the company, via email. The company's reply: Check FedEx's tracking. I tried that, but as soon as I got to that site, I remembered......PartSelect NEVER sent a tracking number for FedEx, whaaaat!!! Needless to say, I'm not a happy camper!!!
  • Patsy from PFAFFTOWN, NC
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time

Measures level of soil in the water.

$ 33.70
  In Stock
PartSelect Number PS11757214
Manufacturer Part Number WPW10705575

Replacing your KitchenAid Dishwasher Turbidity Sensor

Replacing your Turbidity Sensor

Customer Repair Stories

Failed diagonistics test for OWI sensor
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
  • Mark from Lancaster, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
60 of 85 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
22 Reviews

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.

$ 33.09
  In Stock
PartSelect Number PS972325
Manufacturer Part Number 8194001

Replacing your KitchenAid Dishwasher Door Balance Link Kit

Replacing your Door Balance Link Kit

Customer Repair Stories

Door spring link broken
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.

2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.

3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.

4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.

5. Reverse (2 to 1) to reinstall the dishwasher.
  • Sean from Ramona, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
153 of 185 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
  • Scott from Fort Lauderdale, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
629 of 671 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
23 HOUSING
Fixes Symptom 1% of time

$ 32.67
  In Stock
PartSelect Number PS11738118
Manufacturer Part Number W10873429
Fixes Symptom less than 1% of time

This seal is located between the spray arm and the water feed tube.

$ 13.69
  In Stock
PartSelect Number PS11745444
Manufacturer Part Number WP8268433

Replacing your KitchenAid Dishwasher Spray Arm Seal

Replacing your Spray Arm Seal

Customer Repair Stories

top rack not cleaning
remove the top rack remove screw holding spray arm on rack.replace spray arm seal screw spray arm back on rack.
  • DENIS from Almont, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lack of water flow
removed rack
removed one screw
removed old seal
installed new seal
installed screw
  • Geoff from Avon, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time

$ 23.69
  In Stock
PartSelect Number PS11765163
Manufacturer Part Number W10850371
Fixes Symptom less than 1% of time

This part has a large port for the soil sensor and thermistor.

$ 125.97
  In Stock
PartSelect Number PS11746658
Manufacturer Part Number WP8572618

Customer Repair Stories

Leak around gasket
Long story short, noticed one of two leaks and came to conclusion there is no workaround since sump pump gasket seems to be hermetically sealed to sump pump. Which is understandable because of water in area. Wife helped by soaking other parts that were removed and replaced, because of calcium buildup. Which we hope will extend life of dishwasher. I put 1 to 2 hours because I took my time and made sure all parts fit correctly and were back in their original place. Didn't want to take any chances in not covering bases. I am no expert, but definitely a diy'er. I believed I saved myself anywhere from $200 to $300 in labor costs by repairman. By the way, thanks Parts Select your info and site are awesome!!! The second part I had to order was the water inlet valve and your phone representative was a big help over the phone, please don't eliminate those positions. Overall total price of parts approximately $130 w/delivery. Well worth it, since a brand new halfway decent dishwasher starts at $550.
  • reynaldo from San Antonio, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
2 Reviews

Also known as a water supply tube which is used for your middle spray arm.

$ 58.45
  In Stock
PartSelect Number PS11752851
Manufacturer Part Number WPW10323424

Replacing your KitchenAid Dishwasher Manifold

Replacing your Manifold

Customer Repair Stories

manifold wore out did not hold water anymore
remove one philips screw take out manifold replace with new one put screw back in and we are done not mechanically difficult by any means
  • Irl from EMMITSBURG, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time

This part moves water up from the sump collection area and up through the spray arms.

$ 345.91
  In Stock
PartSelect Number PS11757411
Manufacturer Part Number WPW10780877

Replacing your KitchenAid Dishwasher Sump and Motor Assembly

Replacing your Sump and Motor Assembly

Customer Repair Stories

Dishwasher is about 3 years old, motor started makeing load noises.
Cut power and turn off water. Pulled the dishwasher out of the cabinet. Removed internal spray unit. Lay a plastic bag on bottom of tub in case a screw falls from upper spray assembly while removing. Disconnected and drained all hoses. Put down plastic lined tarp on floor. Lay dishwaser on its side onto tarp. Removed hose from recirculation pump, removed water sensor and recirculation pump from housing and detach electric connection. Removed 3 plastic push clips and removed entire motor-pump unit from tub. Position new motor-pump unit into tub. Replace 2 push clips into position, then used a flat screwdriver to put some tension and position plastic pump assembly so I could insert 3rd push clip into position. Replaced all components & reconnect hoses. Turn on water & power. A relatively simple repair. Too bad the original motor-pump only lasted 3 years. Not built like the used to. Thank goodness for Part Select.com Great schematics and descriptions. Excellent website, service, delivery and excellent Part! Thank You!
  • Joseph from Greenlawn, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishes on the top rack weren't getting clean -- Motor was weak
This was a fairly easy repair. It took me a little over an hour to complete. First I flipped the circuit breaker for the dishwasher; then I removed the dishwasher from the cabinet and disconnected the supply, and return lines. I removed both racks from dishwasher, the lower washer arm, and the plastic conduit that supplies water to the upper rack. I then turned the unit onto it's side, and pulled the three or so cables that went to the motor, along with the three plastic wedges that held the motor in place. I then pushed the old motor through, into the interior of the dishwasher. This required me to disconnect some additional components to get it to fit through the opening, including the large silver capacitor. I then compared the old motor to the new one, and transferred some of the parts from the old motor to the new one that weren't included with the new one. I then pushed the new motor through the opening. This required a second person, who replaced the plastic wedges, while I pushed on the motor. The cables, supply lines, drain lines, and components that wouldn't fit through the opening were then replaced; the interior of the dishwasher was also reassembled.
  • Steven from Mahwah, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
17 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
2 Reviews

$ 140.94
  In Stock
PartSelect Number PS11773088
Manufacturer Part Number W11032769

Customer Repair Stories

Rinse dispenser cap came off in the cycle and was damaged
Replaced just cap
  • Nancy from Laguna Vista, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
30 SHIELD
Fixes Symptom less than 1% of time

Shield

$ 38.42
  In Stock
PartSelect Number PS11730934
Manufacturer Part Number W10831329
Fixes Symptom less than 1% of time

$ 8.04
  In Stock
PartSelect Number PS11741626
Manufacturer Part Number WP3400931
32 Lever
Fixes Symptom less than 1% of time

$ 7.42
  In Stock
PartSelect Number PS11750029
Manufacturer Part Number WPW10195037

Replacing your Whirlpool Dishwasher Lever

Replacing your Lever

Customer Repair Stories

Dishwasher was not filling up with water.
First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.
  • Jolene from CINCINNATI, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time

May differ in appearance, but functions same as original. This valve allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.

$ 52.82
  In Stock
PartSelect Number PS11745441
Manufacturer Part Number WP8268375

Replacing your KitchenAid Dishwasher Sump Pump Check Valve

Replacing your Sump Pump Check Valve

Customer Repair Stories

Hose plugged up and noisy when running
Very easy to change
  • Gene from Killeen, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher quit draining
Replaced the Sump pump check valve, but ended up replacing whole pump, still only took 30-60 minutes from start to finish.. Videos helped a ton...
  • James from vista, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time

Supplies water from the main water feed tube to the middle manifold water tube.

$ 34.08
  In Stock
PartSelect Number PS11748182
Manufacturer Part Number WPW10082831

Replacing your KitchenAid Dishwasher Water Supply Manifold Probe

Replacing your Water Supply Manifold Probe
Fixes Symptom less than 1% of time
★★★★★
★★★★★
53 Reviews

This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.

$ 26.89
  In Stock
PartSelect Number PS3406971
Manufacturer Part Number W10195416

Replacing your KitchenAid Dishwasher Lower Dishrack Wheel

Replacing your Lower Dishrack Wheel

Customer Repair Stories

Wheel on lower shelf broke off
Simply snap the old one off and snap the new one on. Simple as that less than 15 seconds.
  • Dennis from OAKWOOD, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
30 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken wheel unit on the bottom dish rack
All you do is pop out the old wheel unit at two (2) points on the plastic wheel housing and pop in the new one. Easy fix. Less than a 5 minute fix.
  • Thomas from WEST OLIVE, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
94 of 108 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time

$ 20.18
  In Stock
PartSelect Number PS11755103
Manufacturer Part Number WPW10462232
Fixes Symptom less than 1% of time
★★★★★
★★★★★
2 Reviews

NOTE: This part has been redesigned, it may appear different but will still function the same as the original.

$ 27.89
  In Stock
PartSelect Number PS8770043
Manufacturer Part Number W10619006

Replacing your KitchenAid Dishwasher Door Latch - Black

Replacing your Door Latch - Black

Customer Repair Stories

Dishwasher would not turn on and door did not latch properly.
New latch assembly improved door closure. However, door latch did not solve problem. There appears to be another problem.
  • Robert from BOULDER, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inoperative door latch replaced by a redesigned latch
1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.
  • Arthur from NEWNAN, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
35 of 42 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
1 Review

The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.

$ 61.89
  In Stock
PartSelect Number PS9494999
Manufacturer Part Number W10703867

Replacing your KitchenAid Dishwasher Dishwasher Heating Element

Replacing your Dishwasher Heating Element

Customer Repair Stories

Defective dishwasher heating element
Turned off water supply to the unit. Removed plastic cover at bottom front. I only had to disconnect the copper water line to slide the unit about 1/3 of the way out. I then was able to reach the wires, disconnect them and use a stubby box/open end wrench (5/8? don't remember for sure) to remove the plastic nuts. I then opened the door, removed the bottom basket and slipped the element right out. Installation of new part was reverse.
  • Matthew from CHATHAM, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heating for washing or drying
Was a cinch just watched the video whole procedure took an hr or so
  • Dewey from UNIONTOWN, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
1 Review

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$ 10.03
  In Stock
PartSelect Number PS11745496
Manufacturer Part Number WP8269145

Replacing your Whirlpool Dishwasher Mounting Bracket

Replacing your Mounting Bracket

Customer Repair Stories

Broken Mounting bracket
Removed old part and replaced with new part
  • Roy from HIGGINSVILLE, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
  • Judith from Essex, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
75 of 108 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
40 Tub Cap
Fixes Symptom less than 1% of time
★★★★★
★★★★★
1 Review

The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.

$ 15.48
  In Stock
PartSelect Number PS11703426
Manufacturer Part Number W10795980
Fixes Symptom less than 1% of time

The spray arm in your dishwasher spins and sprays the water that is used to clean your dishes. If the spray arm is damaged, your dishwasher will not clean properly, and you will need to replace it. Many of our customers have rated this repair as easy, and to complete the repair you will simply need to unscrew the old arm, and replace it with a new one. Make sure the jets are facing upward when you secure the new arm. This part is made of gray plastic and is approximately 18 inches wide.

$ 45.76
  In Stock
PartSelect Number PS11748185
Manufacturer Part Number WPW10082841

Replacing your KitchenAid Dishwasher Middle Spray Arm

Replacing your Middle Spray Arm