KUCC151LPA1 KitchenAid Trash Compactor - Instructions

-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before

Like others who experienced this problem, I removed compactor from under the counter and laid it on its side. I removed the screws holding the cover plates to the motor and gear/chain box. The larger (4" +/-) plastic drive gear which moves the chain that lowers or raises the compactor ram was broke. Using a socket and ratchet, I turned the shaft the gear was attached to in a counterclockwise direction and moved the compacting ram from the bottom position to the top so I could finally open the door, It takes a lot of turns to move the compacting ram to the top so be patient. I then loosened the bolts, in the base, that holds the motor secure and slid the base toward the broken gear putting slack in the chain. I removed the split ring from the shaft and removed the sprocket which originally is part of the gear but was left on the shaft when the gear broke in three places. I elected to not remove the original washer and spacer and put the new gear with sprocket on the shaft, put the chain on the socket and installed the split ring. Slid the motor base back to original position putting slight tension on chain and a proper clearance between the gear and drive shaft (sheet of paper seperation). Reinstalled the covers, tested and was finished.

I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.

I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.

changed out the switch and that fixed the problem

Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

It was very easy. I unscrewed the broken acuator and screwed the new one on. It took less than 5 minutes. Much better than paying a repairman $150 for a service call. This part actually breaks often so I ordered 3 or the future.

pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.

I had expected to just have to install a new spring steel "L" shaped switch operator to replace the one that had broken off. Installation of the new switch and redesigned operator was difficult in tight quarters. Good news, four hours later compactor works as advertised. Hope that the revised design works well and for a long time.

Easy, called a repair person to install...

Step one-read instructions; step two-follow them! Really not that hard. Pull the compacter out. Take four screws off the top plate. Take 8 screws out the face plate. Disconnect old actuator install new one. Put the cutout over the new one. Drill ONE hole with template. Screw the one in. Now drill the second hole out-but make sure its level dont be a tool and make it all crooked. Then screw it in place. Put the face plate back in with the 8 screws and put the top plate back on. Now remove foot assembly and old actuator lever from drawer. Install new rubber thing a bobber and put the foot assembly back together. Put it all back in smack it with a hammer 32 times add duct tape and voila donzo!

First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!

Put the parts in and reinstalled it back in it place

Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.

I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new

This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.