KUCC151GBT1 KitchenAid Trash Compactor - Instructions

REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES

Removed and replaced in less than 15 minutes. Works like new again

Screwed in as far as I could get it but it never went flush with the wall of the compactor like the factory placed ones.

Remove 2 screws to remove front of compactor. Remove old switch by squeezing it together pushing inward. Remove wires and replace on corresponding plugs on switch. Push new rocker switch until it snaps in. Replace front of compactor with 2 screws. Worked like a charm compacting.

Problem is, the filter holder is jammed on its holder and will not come off.Short of using a blowtorch, this is a permanent FAIL!

layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake

I just used the accompanying screw to attach the buttons to the 4 holes in the drawer. Simple stuff.

I do think I read that the Jenn-Air bags used to come with precut holes, and the bag wold slide over the buttons, holding it in place. I jus get the bag lined up and pulled over the drawer, and cut the holes myself. It works perfectly.

Removed drawer
Pulled out from cabinet
Unplugged power cord
Removed top cover
Removed front panel
Put front on 2x4 block
Unscrewed leveling legs
Used 9/16" socket to remove old rollers
Installed new rollers
installed front panel
installed top panel
Plugged in electric cord
slid back into cabinet
inserted drawer
tested
Works as good as new

Took the 2 screws off the front, popped the switch out, copied the wires on to the new switch, and put it back. New switch does not have a light, so had to eleminate one power wire, put it back together, and it worked just like new.??

Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

1)Pulled the unit out remove the top and bottom covers. 2)Disconnected the drive chain by removing the sproket from the motor. 3)Unscrewed the drive rod on the side that worked and removed the ram. 4)Reassembled and used the bin for trash while waiting for the part. 5)The nut came with clips included (this was not noted in the order but is vital) removed the stripped nut by breaking the old clips. 6)Installed the new nut, clips on the ram. 7)Installed the ram onto both drive screws. I had to hold the 'top sensor' switch up to reverse the screws to lower the ram. 8)Rinstalled the top and the appliance. 2 thru 4 dealing witht the chain, sproket and screw were fairly complicated operations.

Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the drive gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.

There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.