KSRP25FNSS00 KitchenAid Refrigerator - Instructions

I watched the video showing how to disassemble unit and it showed that there was a heat element inside the chute door under the foam seal that needed to be removed and placed in side the new chute door. I spent about 10-15 minutes trying to salvage the element but the adhesive used would not release and the part was rendered unusable. I called the help line and was told that their instructions on that kit said the heating element was no longer required. I finished putting the kit in and the unit works fine

Unplug the Unit first! Unscrewed the sensor covers on both sides. Snap off the old, snap on the new. Replace the covers and screws.

I was hesitant about calling the repair line, I thought it was a gimmick, but tried anyway since it was close to the 4th of July weekend. The repairman asked a few questions and diagnosed the problem. He said the sensor was out on the ice maker and I would have to get a new one, he gave a link to the part I needed. I was still hesitant, as I know very little about repairing appliances. Thought about it for an hour, decided to order the part, and thought I would call a repair man if all else failed and send the part back. I received the part in 3 days and it didn't look too difficult to install, I decided to give it a shot, all i have to do was take a few screws out, remove the old ice maker, and put the new ice maker in and plug it in and attach the screws, it went real well, the hardest part was finding the right size socket to fit on the screws, I turned the water back on and it didn't leak. The next day I had ice, still can't believe I did it myself. I was extremely pleased, that I didn't have to call a repairman and take a day off from work to get it fixed. I will use this sevice again.

Replaced the Ice Maker

Removed hinged door from front of ice maker. Removed screws from bottom of ice maker. Removed ice maker unit and replaced control board. One pin connection was burnt. Reassembled unit and it works fine.

Followed the steps in the video on your website, and was amazed at how simple and fast it was done, with no problems.

Ice door would not close thus letting warm air into the freezer compartment. Thinking the spring was broken, I ordered the Ice Door Kit. When it arrived, I dismantled the dispenser and installed the new parts. After installing all the new parts, I found that my problem was the "Y" end of the bracket that holds the spring pin. It was cracked and would not hold the pin. The bracket seemed to be molded into the panel on the outside of the dispenser. To replace the bracket, I would have had to replace the entire outside panel. I decided to repair the bracket and glue the broken piece. I used cyanoacrylate(CA)super glue that I use in model making. Even though that seemed adequate, I decided to drill a small hole through the bracket, perpendicular to the crack, and install a small screw to strengthen the crack. I also applied a little CA to the screw for good measure. It held fast and so far so good!

We were reluctant to replace the icemaker on a 10-year old refrigerator that required a leak to be patched 2 years ago, but since the patch seems to be holding, we went ahead with the icemaker. Was about the same price as buying a portable icemaker and who wants that sitting on the counter?

Removed the broken icemaker. Removed the tray that is attached to the old icemaker and screwed it into the new icemaker. Then, I installed the new icemaker first by plugging in the control wires, then sliding the icemaker into the freezer, then screwing it into freezer. BY next morning, the icemaker made ice!

Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

Ordered part and w/ help of a friend in it went.Devlivery was prompt. Receptionist on phone was great. If every company had one like her everyone would be a happy camper.Would recommend your company to anyone.It was a most pleasant experience.

Neither the OEM instructions nor any of the PartSelect videos explained BOTH ends of the tube for my particular appliance. All very thoroughly covered the obvious connection with the water valve from the wall. However, the push valve end for my KitchenAid is supposed to insert into the water filter chassis, which can barely be seen from the back of the appliance, much less reached with any tool. In order to make the repair, one must either remove the water filter chassis (which I attempted unsuccessfully), or put the appliance up on jacks in order to reach the push valve site.

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

pop in and presto! simple, no tools required, perfect fit.

Replaced the two circuit boards