KSRG25FKSS16 KitchenAid Refrigerator - Instructions

1) At bottom of ice maker trim there are two small slots at right and left ; use screw driver to pry away from door; lift trim upward away from door 2)using 1/4" nutdriver remove screws from 4 corners, 3) remove 2 screws from control panel 4) disconnect all wires/cables and set exterior panel aside. 5) locate 2" pin that runs through door spring and use needle nose pliers to remove round clip on left end of pin don't lose this clip 6) while pushing ice maker lever (where you would push with your glass) use needle nose to pull the long pin out to the right 7) Remove all remaining parts by hand (i.e. the pin, the dash pot and white lever and the ice door) 8)slide new control lever into slots on exterior side of the new door 9) -tricky part- using needle nose, push pin back through the right hinge point, the new lever, the new door, the new spring and the left hinge point (note the new door has no electric wire connector) 10) using the needle nose, carefully replace the little round clip on the left end of the metal pin. 11) reconnect all the wires (don't worry about the wire that had been connected to the door wire, just fold it aside) 12) replace two screws screws in control panel and four screws at corners of exterior panel 13) snap outer trim panel back in place.

I removed the ice maker which required removing 3 screws and then disconnecting the electrical plug. Once the ice maker was out, I removed the 3 screws that held the motor assembly to the unit.
I removed the motor, replacing it with the new one.
Plugged the power supply cord back in, replaced the unit with the 3 screws and within a few minutes the unit was receiving water and by the next day I had ICE. This saved me $50. for the service call, then another $25.00 installation fee when the part came in (had to be ordered) plus the markup on the motor (approx. $25.00) So I saved approx. $100. and only took about 30 min.

1. turn off power.
2. pop off ice maker cover to access motor assembly.
3. remove three screws to assembly.
4. pull off assembly.
5. attach new assembly making sure metal arm and plastic
ice tray rod align with assembly.
6. screw assembly onto unit.
7. replace cover.
8. plug in refrigerator.
9. enjoy ice again with no leakage into freezer.

While looking for parts I read the advice on you web site under the ice maker parts. I also had problems reading the LED codes. They would change each time I unplugged the refrig and powered up. I took the other guys advice, ordered the emittered and receiver and the next morning I had ice. GREAT service guys, thanks. Also the part was on my door step in 1.5 days. Sure beat an expensive service charge.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

First I removed the bolt that holds the cover on the top hinge bracket. Then I removed all items from the shelves inside the door by lifting the shelves out and placing them on the counter. Next I removed the 3 screws holding the hinge bracket on, this disconnects the top of the door from the cabinet. Then I lifted the door off the lower cam, removed the screws that held the cam in place on the door and the lower bracket on the cabinet and replaced the cams. I smeared some Vaselene on the cams and placed the door back on the lower cam, reconnected the upper hinge and replaced the hinge cover. All done and it works great!

We weren't sure if the problem was in the Water Inlet Valve or in the Icemaker Control & Motor Assembly. The water in the door did work. We removed the Water Inlet Valve & tested it with an Ohm Meter. It tested good so we put it back in. We then ordered the Icemaker Control & Motor Assembly. When it arrived we installed it and waited a few hours but the icemaker still did not fill with water. We telephoned a parts store and were told the problem could be the thermostat or we could replace the whole icemaker. We replaced the whole icemaker.

After repairing a similar refrigerator's ice maker a few years ago, I thought I'd try it again. After some brief research online the compressor tested ok. I ordered the start relay and run capacitor and cleaned the coils. The parts arrived promptly and I installed them without a hitch. The fridge has been working great.

It was simply a matter of removing the old filter housing unit by unscrewing 3 screws and unplugging the two water tubes. After re-insterting the water tubing and securing the housing unit "VOILA" good as new..It really was easy..

The first step was to go to PartSelect.com to find where the filter is located because that is not revealed in Whirlpool's Guide. This refrigerator came with the home I had just puchased so Iwas unfamiliar with the filter replacement. Th filter is on the grill at the bottom of the refrigerator. I followed the instructions helpfully printed on the replacement cartridge box which arrived in less than the 3-5 days acknowledged on my order.

Turn the filter handle 1/4 turn counterclockwise. Don't be timid. It was very tight (probably had not been replaced ever). Remove the filter from the handle that protrudes through the grill at the bottom of the front of the refrigerator.

Insert the new cartridge into the filter handle insert snugly until it goes no further and turn 1/4 clockwise.

The instructions on the replacement cartridge tell you to run the water for 5 minutes to remove air and sediment from the system. DO NOT skip this step. I was. I discovered a large amount of sediment after even three minutes of flushing. A 5-gallon pale will help. And don't forget to turn off the ice maker while you are flushing. Otherwise you will end up with ice cubes everywhere as you try to position the bucket under the water dispenser.

First I unplugged the frig, and turned offed the water and ice dispenser using the on/off panel switch. I removed the panel by inserting a small flat blade screwdriver at the bottom of the panel where the plastic studs locked the panel in place. By inserting a little upward pressure, the panel popped right ouff. The Micro Switch was very easy to remove and replace. Just make sure that the plunger on the ice dispenser makes solid contact with the switch when depressed.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Replaced the door cam on bottom of fridge door. ONE THING TO UNDERSTAND- THERE ARE 2 CAMS ON THE DOOR, LOWER AND UPPER, BUT THE UPPER CAM IS NOT LISTED ON THE "DOOR HARDWARE" DRAWING, ITS LISTED ON THE MAIN BODY DRAWING! BE SURE TO GET BOTH CAMS! (PARTSELECT COULD MAKE A NOTE THAT WHEN PEOPLE LOOK UP LOWER CAM, PUT A NOTE IN THERE SAYING Y0U NEED UPPER TOO!)So I had to order the upper cam later and install later. BUT it is quite easy to replace, unlike the video, I only needed 1 tool! The nut driver (electric screwdriver w nut driver head). Thanks -RF

If you remove the bottom vent panel of the refrigerator there are two schematics for the refrigerator. One for the fridge and one for the icemaker. The icemaker has an emitter and a receiver that will tell the icemaker when it is ok to dump ice and add water. The receiver has an LED that blinks different codes. The codes give you an idea where your problem is located. In my case it coded out to be the optics (emitter and receiver). Replacement of the parts involves the removal of three screws on each component and disconnecting a wire harness on each component. Install the new components by following the removal process in reverse. The total cost was $80.00. This was half the price Sears wanted for the parts and about the same price to have a Sears repairman just show up at the house.

My icemaker wouldn’t pop out the ice. I bought a used fridge from 2nd Time Around in Russellville AR which was the most horrible customer service experience of my life. They were supposed to have a 60 day warranty but didn’t follow through. After months of begging them, and knowing what part I needed, I just ordered it myself. It was so easy and quick and fixed my issue my husband said we should have done that months ago and avoided the hassle. It was worth the money to have the peace of mind. Now everything is perfect! All we had to do was remove the icemaker, take off the side with a screwdriver, replace the part and slide it back in. We had ice in hours! Shipping was quick (a couple days) the part was 30 dollars cheaper than other places I checked. We love it!