Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSM90PSER0 > Instructions

KSM90PSER0 KitchenAid Mixer - Instructions

All installation instructions for KSM90PSER0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSM90PSER0
31-45 of 215
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Mixer only had 2 speeds with the smell of electrical burning.

  • Customer: Michael from MONTROSE, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
This mixer was given to me 8-10 yrs ago with only 2 speeds (cant believe i waited this long to fix it). Repair went good, wasn't sure what i should replace so i replaced Control board, control plate, governor, grease in the gears and the transmission gasket. I first took any and ALL measurements for any screws on the control plate, this will help when you set your mixer speeds when its all back together. When installing the new governor i used a 10mm socket and a mallet to seat it all the way till it stops on the set pin. installed the new control board, with thermal grease on the back of the plate(very important). Didn't need to replace the grease in the gears, but i figured since i was in there id replace it. (No smells and all gears work) I used it to ground 5lbs of elk into burger (speed 4) after repairs and it worked great. Still have about 15lbs left to do and itll do it with out braking a sweat. Maybe i should open up a repair shop to fix these suckers...lol its that easy. What really helped with the repairs is the youtube video from Partselect. Second to none with a step by step on how to replace and repair just about anything on your mixer. Good deal, if i need to replace anything else i know where to go! Thanks

The coating was chipping off of the original Flat Beater

  • Customer: Pat from Marshfield, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
All I had to do was insert the new beater. Wonderful timing, was just going to start some holiday baking. will definetly use your website again. Thank you.

spent Pevel Pinion Center Gear

  • Customer: EUGENIO from MIAMI, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.

When using the bread hook, the force of the dough would knock the bowl out of the retaining ring on the mixer (Cap-Screw.)

  • Customer: Jerry from Burnsville, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.

Plastic boke on the old thumb screw

  • Customer: Alice from St Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

Worm gear broken

  • Customer: Jennife from Lancaster, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 5 of 9 people found this instruction helpful
I called my fiancée.

broken wire whip

  • Customer: Stanislaw from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
no instructions necessary

Replace base plate on KitchenAid mixer

  • Customer: Joyce from Great Bend, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Took out 3 screws, removed old plate, put down new plate the tightened screws. Runs like new, great service, price, quick delivery!

Broken worm gear

  • Customer: Edward from Edgewater Park, NJ
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Removed old gear and grease and replaced gear and grease resembled

powder coating came off mixer paddle.

  • Customer: .JENNIFER from STAR, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
put new paddle on

The worm gear was broken

  • Customer: DONG from Elk Grove, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok

plastic outer casing on tightening screw had broken

  • Customer: Peggy from Escondido, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

Base plate destored

  • Customer: Gordon from West Stockbridge, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

Pin was missing on mixer allowing head to move.

  • Customer: James from Columbus, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 20 people found this instruction helpful
Inserted new pin and tightened set screw.

Attachments would not work, spindle turned erratically, with no power

  • Customer: Kerry from Sherwood, OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Punched out the roll pin to remove eccentric from spindle, undid 5 screws (after removing trim ring), and removed 4 screws to undo the motor housing. Make sure to keep the one screw with a lock washer in the BACK of the housing. Undid the screw on top to remove the back of the motor housing to take out the strain relief grommet, prior to removing the motor housing. Scraped the excess grease into a tub to re-use. Pulled out the shaft, and lifted out the old (stripped) gear and plopped the new one in. Make sure to mark match points for parts, and put the pins back in in the right order. You have to put the 5 screws back in before sliding the trim ring on, and putting the roll pin back. make sure all gears mesh and test before snugging the motor housing screws. Be sure to orient the strain relief grommet securely, and be careful of the filter plates in the back of the housing (they're brittle). putting the grease back is like frosting a cake. Save a little for the planetary ass'y.
All Instructions for the KSM90PSER0
31-45 of 215