Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSM90PSBC0 > Instructions

KSM90PSBC0 KitchenAid Mixer - Instructions

All installation instructions for KSM90PSBC0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSM90PSBC0
16-30 of 215
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken thumb screw

  • Customer: Kathleen from Silvis, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
remove the old screw and screwed the new part in place. I like your link because it shows a picture of the fixture and you can find the part you need real easy. Will order from you again when I need it.

I broke the motor brush when I was taking my mixer apart for some serious cleaning

  • Customer: Veronique from Loganville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 17 people found this instruction helpful
unscrewed the screw holding the old brush. carefully removed the spring and old broken brush. we did have some of the old brush left inside, so my husband used a very thin drill bit to break it up. then carefully inverted the stand mixer to allow the broken pieces to fall out. then we were able to install the new brush. works great. yeah!!

Nut Screw Plastic Housing Split that stabilizes attachments on top side of machine

  • Customer: Richard from Bayfield, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 8 people found this instruction helpful
I removed the old screw with a hand tool to avoid injuring my hand. I then used my hand to install the new screw. Piece of cake. Ordering from Part Select was was a breeze. The only minor issue was the part cost $4.33 and shipping was $7.25.

screw cap would not hold bowl when making dough

  • Customer: Carrie from Jeannette, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
My kitchenaid mixer is at least 37 years old. Everything has worked fine after all these years except the screw cap was flimsy, still stainless steel, but not sturdy. So I tried to replace it , but was told it was too old and couldn't get the part. I contacted Part Select and found a screw cap from newer models fit perfectly and should outlast me and the mixer, it is a lot sturdier than original one. It also arrived in 2 days, which was fantastic. Thanks guys

gear was stripped , head wouldn;t turn

  • Customer: Joan from Nokomis, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
We followed the you tube instructional video. It was excellent with good advice that kept us out of trouble. My mixer works like new again.

The mixer got a wad of dough between the pan & beater and stopped.

  • Customer: Charles from Bowie, MD
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 8 of 9 people found this instruction helpful
Once I looked at the schematic I was prtty sure what the problem was and what I needed to repair the problem. It was reltively easy to disassemble the mixer and immediately saw that I was correct in what was needed. I ordered the parts. They came through with no delay. It took almost as long to find all of the parts as it was to do the repair. In all it took about a half hour to repair, put it together and clean everything up. It works just like new.

Moter would run, but nothing would turn

  • Customer: Curtis from Green River, WY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
first removed the dress ring by tapping it very gently.then drive the pin out that holds the beater plate on, now wiggle it off, then you can see the screws that hold the gear reducer on. remove them. take that off and you will see the housing that hold the worm gear. remove the 3 screws that hold it down . Now you will have to drive the drift pin out that holds the worm gear in place, slide the shaft out then remove gear. reverse order to assemble

replace burnt power cord

  • Customer: Richard from Alliance, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First I removed the back cover, two wires just unplugged and one wire I had to remove a screw, then put on the new wire, plug the two screws on, screw on the third wire and put the cover back on.

broken gear

  • Customer: angelo from palm coast, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
remove 6 screws for top of unit, remove gear assymble (23 screws), reassmbly and test it works great

my Kitchen Aid mixer had one speed - HIGH!

  • Customer: Darcy from Eyota, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 10 of 17 people found this instruction helpful
I actually didn't do the repair. I asked a friend who was a carpenter about what he thought was wrong with my mixer since it only had high speed which made mixing flour a snow storm. He said when his tools do that, it's the brushes. He ordered new ones and presto - my mixer works marvelously. He saved me from dumping a good mixer and $$$$$$$.

wire broke

  • Customer: Carol from Rochester, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
total replacement
works beautifully

Stripped gear when I tried to make Pizza Dough

  • Customer: Patrick from Cupertino, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Very messy as there is lots of heavy grease inside the mixer and you have to fish out the blown gear parts. I vary glad I took shop class in High school as it preped me for the job. The machanical drawing you provide were very useful but you should mention the grease.

Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday

Worm gear was missing teeth

  • Customer: Terry from Pigeon, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Took the mixer apart and cleaned the grease so off I could see the pins. Wasn't a hard fix only thing is make sure to clean the grease off so you can see what your doing

Mixer only had 2 speeds with the smell of electrical burning.

  • Customer: Michael from MONTROSE, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
This mixer was given to me 8-10 yrs ago with only 2 speeds (cant believe i waited this long to fix it). Repair went good, wasn't sure what i should replace so i replaced Control board, control plate, governor, grease in the gears and the transmission gasket. I first took any and ALL measurements for any screws on the control plate, this will help when you set your mixer speeds when its all back together. When installing the new governor i used a 10mm socket and a mallet to seat it all the way till it stops on the set pin. installed the new control board, with thermal grease on the back of the plate(very important). Didn't need to replace the grease in the gears, but i figured since i was in there id replace it. (No smells and all gears work) I used it to ground 5lbs of elk into burger (speed 4) after repairs and it worked great. Still have about 15lbs left to do and itll do it with out braking a sweat. Maybe i should open up a repair shop to fix these suckers...lol its that easy. What really helped with the repairs is the youtube video from Partselect. Second to none with a step by step on how to replace and repair just about anything on your mixer. Good deal, if i need to replace anything else i know where to go! Thanks

The 5 feet on my Kitchen Aide, had worn out

  • Customer: Beverly from Post Falls, ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Took the old feet (5) off and put new on the Kitchen Aide, looks great. Stands high and your assistance on the phone, was so appreciated.
All Instructions for the KSM90PSBC0
16-30 of 215