Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This EveryDrop Filter3 is certified to reduce the most contaminants with Triple Filtration Technology. Now, you and your family can enjoy the enriching benefits of cleaner, freshly filtered ice & wate...
The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack ...
This Ice Maker (Icemaker Assembly, Complete Icemaker Assembly, Ice Maker Assembly, Refrigerator Ice Maker) can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located ...
The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns th...
This is a refrigerator ice guide that is made entirely of clear plastic. This ice guide is located in the freezer door. Turn your refrigerator ice dispenser off before replacing the part. This is a si...
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-met...
This light bulb is a 120 volt, 25 watt incandescent appliance light bulb with a small base screw-in that fits in a variety of appliances such as microwaves, refrigerators, freezers, cooktops, or stove...
In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute t...
This set of two electronic control boards contains both the emitter and the receiver. These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker whe...
$379.56
In Stock
Questions And Answers for KSCS25INSS00
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
14 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
March 17, 2020
The outside of the wall between the fridge and the freezer seems very hot. I'm talking about the area where the doors close to. I checked it with my infrared thermometer, it is 147 degrees. The fridge and the freezer seem to be working fine, it keeps things at the proper. Is this normal?Thanks
For model number KSCS25INSS00
Hello Jim, thank you for your question. It is normal for this part to be quite warm, but it should not be as hot as you are describing. The condenser fan motor, PartSelect number PS1957416, is more than likely causing this issue. You will want to check this motor to be sure it is running as it should. If there is debris blocking the fan blades from circulating the air over the condenser coils, this symptom may arise. If there is nothing blocking the fan blades, and the motor is not working as it should, it is recommended that this part be replaced. We hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Danny
March 6, 2025
My refrigerator runs for several hours then turns off and beeps and the lights flash, has anyone had that problem? What could it be?
For model number KSCS25INSS00
Hello Danny, Thank you for contacting us. Researching your model, this usually indicates an issue with the control board or the wiring. We would recommend checking the main control board and inverter board for the compressor. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Frank
July 13, 2021
Lost freezer and cooler temperature
For model number KSCS25INSS00
Hello Frank, Thank you for the question. If the Temperature inside the Freezer is too warm, we suggest testing the Bi-Metal Defrost Thermostat. The best way to do this is to remove the Thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps
Model was manufactured 2005, can you give me dimensions and compartment capacity. Unfortunately it is getting old and needs to be replaced. Thanks
For model number KSCS25INSS00
Hello Tim, Thank you for contacting PartSelect.com. Very sorry but we do not have the size of the appliance, just parts lists and diagrams. For more specialized assistance or to speak with someone about this, we would suggest calling the manufacturer of the appliance directly. We hope this helps!
Was this helpful?
Thank you for voting!
Michael
January 22, 2020
Light bulb quit working and tried new e17 bulb from 3 different sources. The good bulb on the other side worked in the socket with the bad bulb, so socket seems ok.
For model number KSCS25INSS00
Hi Michael, thank you for your question. If your light is still not working then you may have to take a look at the socket, wiring, and light switch for being the issue. Good luck with your repair.
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours.
Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the ri
... Read moreght side. You're done! Reverse procedure for installing. Good luck. Remember, your working with cold plastic...take your time and don't force too much.
