Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
841-855 of 1,448
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker was not making ice

  • Customer: SHARON from Post Falls, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The comments from PartSelect were 50/50 that it would be the motor on the icemaker. We bought the motor which came 4 days leter and followed the installation instructions in the video. We started getting ice about 2 hours after the installation!

Would not make Ice

  • Customer: Len from Apple Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn the unit OFF - Removed one hex head screw on the bottom of the ice maker, removed the cable cover and unplugged. Removed front cover & Slide the icemaker out. Removed control cover and removed the three phillips head screws to the controller. Put the new controller back on with the three phillips head screws, pushed the cover back over the controller. Plugged the unit back in, then slide it back in the tracks, put the cable cover back on and installed the hex head screw, popped the front cover back on and turned the unit ON - DONE!

Ice Maker Stopped Working

  • Customer: Susan from Flemington, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
My dad and I worked together. The video helped but it was a little more complicated. If you can't find the water supply, remove the filter and water should stop, that's what we did. We had to remove the freezer door for access to the ice maker. It was tricky taking the icemaker off and getting it back on. Replacing the motor was easy, just as shown in the video. Just like others have said, within an hour of the repair the ice starting coming!

was not making ice

  • Customer: Ricky from Nashville, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Thanks to this site, it told me what was wrong, what to order and how to repair it.

Ice maker quit

  • Customer: Ann from Raleigh, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
2 screws...removed old part Module Assembly..put in new and was set to go!

Door not staying closed

  • Customer: Josh from Snohomish, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

Water overflow from ice maker turns ice in tray into block

  • Customer: Patrick from Las Vegas, NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Symptom: The ice maker was making ice, but sometimes the water would run and overflow at the entrance of the ice maker, spilling water into the ice catch and turning all of the ice into a huge block. The problem was that the liner of the ice maker had started to flake off, but only on part of the unit. When water would flow into the ice maker, the exposed part would freeze quickly, creating an ice dam and block the rest of the water from flowing into the other trays, thus overflowing. Solution: A new ice maker unit was ordered online, then after watching the video on how to fix, the process was straightforward and fairly simple. There is one screw to remove, 2 to loosen, and a wire harness to remove to remove the ice making unit. Then the ice full bar was removed from the old unit and put onto the new unit and the entire assembly replaced inside the freezer. The most difficult part of the job was loosening the screws by touch as there isn't a lot of room to see.

Icemaker not making ice

  • Customer: Gerard from Dublin, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I had to make sure the electronic beam was working properly, which it was (steady beam if you press in the side plastic flap. I also had to make sure the water valve for the icemaker was working properly as well, which it was by switching the lead wires on the valve (water dispenser wire to ice maker valve, and hitting water dispenser paddle and hearing water flow to the ice maker). After that, I knew it was the icemaker motor. Removed three screws with a socket, disconnected wire harness (had to use pliers to pull it apart), pulled out entire icemaker unit. Loosened three screws on motor control unit to remove it from icemaker unit, then inserted new motor control unit and re-screwed the 3 screws. Then I pu tthe entire icemaker unit back in the freezer, connected wire harness, re-inserted three screws and was finished. I then waited for one hour, went to check ice maker and I had ice cubes forming in the tray.

Ice maker began making large block of ice, although still made cubes, bur required emptying weekly.

  • Customer: John from Carrollton, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged, turned off water. Simply took out bottom screw, then two top screws. Disconnected writing harness. Put in the new reversing order. Then like new again!

Coating of Mold deterioated and mold leaked into ice tray

  • Customer: Dwight from Bossier City, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video on Parts Select and it was a breeze.

Stopped making ice

  • Customer: Erin from Indianola, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have a side-by-side fridge/freezer, so taking out the icemaker is a bit more tricky than the video shows. I just unscrewed a nut in the back right of the mechanism (this nut is holding the icemaker in place as well as the plug cover). Once that was off it slid out pretty easy. Because the freezer is so narrow, it's a bit difficult to get it back in, but all told the repair took me about 20 minutes. Replacing this part fixed the icemaker immediately and we're so glad to have our on demand ice back! Ladies, don't be afraid of a little appliance repair!

Malfunctioning Icemenaker - No Ice

  • Customer: Joseph from Davie, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove entire ice maker unit from freezer to test for function. Determined to be an electrical malfunction issue. Installed replacement ice maker unit. Easy fix, perfect fit replacement unit.

Icemaker quit working

  • Customer: James from Fenton, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Researched the problem on the internet. Identified the icemaker control and motor assembly as the most likely culprit. Ordered a new one. Arrived in two days. Installed it in about 15 minutes. Had ice 3 hours later.

ice tray leaked forming blocks of ice in the ice tray

  • Customer: Fred from Taylor Lake Village, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simnple that I let my wife do the repair. All she had to do was to turn of the water supply and unplug the refrig. loosen two screws on top and remove one screw on the bottom of the ice maker. Gentle tilt the unit in order to unplug the electric connection on the rear of the unit and then take it out. The new unit went back the same way in reverse order.

Ice Maker stopped

  • Customer: lRonald from McCordsville, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the ice maker, which consist of three 1/4 inch screws to install the water fill cup and bearing. One must loosen the front panel of ice maker to install the fill cup which consist of two standard screws, slide forward enough to install new fill cup. The removal of the Icemaker control was simple, using #2 phillips screwdriver and three screws. Unplug the control and install the new one, replace the three screws and cover. Reinstall the ice maker and within one hour cubes were dropping in the bin. I saved a lot of money repairing myself, which more than covers the shipping cost. Shipping was fast, two days.
All Instructions for the KSCS25FKSS02
841-855 of 1,448