KPDI620T5 KitchenAid Dishwasher - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First I removed the screws holding the broken mounting brakets in place on both the left and right side and replaced them with the new brackets. It was relatively easy and now the 15 year old dishwasher in addition to still working well is held securely so that it doesn't lean forward when both upper and lower trays are extended.

I removed the clip holding the old tube in place, pulled it off where it was attached to the upper rack hub and removed the cone shaped coupler from the back end of it. Attached the coupler to the new tube, pushed the tube onto the hub and re-attached the clip. Started up the dishwasher after putting in a few glasses into the top rack and they came out clean! Amazing how functional parts make a difference. BTW, the new rubber tube arrived 2 days after I placed my order... very quick service. Thank you very much.

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

I turned off the CB for the DW and the water supply to the DW.
I disconnected the electrical connections on the water inlet valve. I then removed the panels from the lower part of the dishwasher, I pulled the water inlet line off and then the water return line off.

I replaced the valve. The only problem I ran into is that the inlet portion required a new brass "ell" - the one that was on the old piece would have of course been ok, however, it was solidly in place in the old water inlet valve

the only other issue, and one that would probably be commonly encountered - when I first went to turn off the water supply to the DW, the valve leaked - I was fortunate to be able to take the valve apart, clean it and put it back in place

PartSelect web page helped me determine the problem and the solution. It took me longer to read the fix-it directions than it did to fix the dishwasher. Just push the part in the hole and twist. When my wife got home she was so impressed that it was fixed and we didn't spend a huge amount to have a repairman come to our house. I got so much prasie that I didn't tell her how easy it was to do the repairs

First I tried duct tape until I could figure out how to get the part. I went online and found that part that I thought it was, but I wasn't sure since the tube I had was very stiff and looked like it had a particular shape on each end..the one on the site was just a straight tube. I removed the old part which was easy, it pretty much fell off and then pushed the new one on and it conformed to the ends needed since the rubber was soft. It was so easy and the machine works really well again!

Had to cut one end of old tube off with pocket knife, other end was cracked and came right off. Put a dab of vasoline in each end of new water tube and slid in place. Wife had called a repair shop, was told $25.50 for part, $65.00 house call/labor. Easy fix with 15.00 +/- part and 10 min. of my own labor.

pulled old actuator base off, followed instructions on how to install new actuator - followed them -
piece of cake.

Thanks

I first removed the old rubber water delivery tube ( not hard to do since it was literally falling apart from age). I then used a blow dryer to make the new rubber water delivery tube a little more flexible. I slid it on one end and then the other. My dishwasher works great now. The part was very reasonable ($15 with tax & shipping). Last month I had paid Sears to come out to just look at my washing machine and it cost $139. Then the part was going to cost $200 with another $139 because they would have to come out again. I ended up buying a new washer. I was so excited that I was able to fix my dishwasher, I've been telling everyone.

I was told I needed a whole new dishwasher arm, that I probably would not be able to change myself. Described the part of the part in your description area and lo and behold, there it was..
Could not find it anywhere else.
Very proud of myself for fixing it. I did not need any tools. Just removed the old corroded tube and attached the new one.
thanks so much for the web site images and descriptions. (And I normally am very computer /technology challenged) Very user friendly site

Srewed it back on. . . Very simple!

First I removed two lower panels at bottom of dishwasher beneath the loading door using nut drivers. There had been a problem in that the dishwasher was not filling with water during any of the cycle. I closed the water supply. I removed the old water inlet valve completely using pliars to open the hose clamp at the outlet anbd remove the hose. Then used a I/2 "" wrench to remove the copper inlet line. Then I used a screw driver to remove the inlet valve mounting screws. I put the valve in my garage vise to remove the pipe fitting. Everything was reusable on the new valve. I just cracked opened the water supply to make sure water pressure was available to the valve inlet side and reassembled everything. Started the dishwasher and problem solved.

Used duct tape to hold the old tube in place until I had a chance to see if the part was available online. Found it, ordered & received it the very next day. (Great service!) Removed the old tube which was already half off once I removed the duct tape & slipped the new tube on. A little trouble at the rounded end, but I used a screwdriver handle to kind of mold that end round & then slipped on.

I followed advice already posted and applied some liquid soap inside each end of the tube. Perfect!