Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KLFF15KSWHY0 > Instructions

KLFF15KSWHY0 KitchenAid Freezer - Instructions

All installation instructions for KLFF15KSWHY0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KLFF15KSWHY0
76-90 of 203
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.

  • Customer: Mike from Camas, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simply removed the old and replaced with the new part.

Movers broke the icemaker water fill tube shoving my refrigerator through the front door.

  • Customer: Christopher from Valley Village, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.

oven light burnt out

  • Customer: William from Schwenksville, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Refrigerator was freezing up and not cooling fresh food compartment

  • Customer: Greg from McLoud, OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sent power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.

freezer and food section too warm

  • Customer: William from Milford, MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 1 of 2 people found this instruction helpful
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.

burned oven bulb

  • Customer: Ivanka from Atlantra, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 8 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

fan motor had gone bad

  • Customer: william from whitwell, TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 2 people found this instruction helpful
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

noisy fridge, perimeter of door heating up

  • Customer: craig from maple grove, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 2 people found this instruction helpful
figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.

  • Customer: James from Howell, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.

The freezer worked but the refrigerator wouldn't cool.

  • Customer: ROBERT from KIRKWOOD, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
When we got the part, we read the instructions, which were easy and very clear step by step. Taking the old part off took most of the time, it was attached a little differently than was described in the video and the instructions for the part. Once we detached that, the replacement part went in very easily and quickly. It took a short while for the cycle to start, we were actually a little worried that it wasn't going to work. Then it started cycling. After the first day the freezer had started icing up, we took a blow dryer and melted it and waited. It hasn't started freezing up again. The refrigerator is keeping the proper temperature and the freezer is also working properly, it's been a week. We seem to be obsessed with going out and checking to see if it's working but I think it's a success. Doing this ourselves only cost $26.00. A huge savings if we had hired someone else to repair it for us. We will definitely choose this option with any other appliance that needs repair. It was easy and simple to find the correct part thanks to the website. And the video tutorial was very informative and helpful.

CONDENSER FAN MOTOR REPLACEMENT

  • Customer: David from WALTERBORO, SC
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I WAS NOT ABLE TO FIX MY REFRIGATOR DUE THE FACT YOU SENT ME AN EMPTY BOX. WHEN I CALLED TO INFORM YOUR CUSTOMER SERVICE REP, I WAS TOLD TO REORDER AND I WOULD ONLY HAVE TO PAY ANOTHER $24.95 FOR TWO DAY SHIPPING. PLUS THE PRICE OF ANOTHER MOTOR. I WOULD HAVE THE FIRST PAYMENT RETURNED IN TWO TO SEVEN DAYS.I ASKED FOR A REFUND WHICH I STILL HAVE NOT RECIEVED.I PURCHACED ANOTHER MOTOR KIT FROM AMOZON FOR LESS MOMEY AND HAD FREE TWO DAY SHIPPING.STILL LOOKING FOR MY REFUND. NEXT TIME PUT A MOTOR IN THE BOX. TRUE STORIE.

Old tube had cracked due to being frozen....

  • Customer: Stephen from Greensboro, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I followed the simple steps outlines in the great video! Thanks

cooling fan quit

  • Customer: George from Belhaven, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
Ordered new fan motor on line took out old motor and replaced with new one

light bulb went out in my oven

  • Customer: Janet from Ada, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

The Light Socket Burned Out.

  • Customer: MATTHEW from STOCKTON, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 9 people found this instruction helpful
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
All Instructions for the KLFF15KSWHY0
76-90 of 203