KHMS145JBL0 KitchenAid Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Grill
-
John from W. Dover, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic on original grill clips broke.
Took out 2 phillips screws on top, pulled the old grill out, hooked the tabs on the bottom of the replacement into place, positioned the top of the replacement, and replaced the 2 screws. 5 minutes. NOTE: Save the screws, new ones don't come with the replacement grill.
Parts Used:
-
Ken from DALLAS, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my pan that browns the meat started to bubble and peal
I really did not have a repair on the microwave just a replacement of the browning pan
Parts Used:
-
Lillian from SAN JOSE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud buzzing noise and no heat.
PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.
Parts Used:
-
Charles R from Libertyville, IL
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken handle (top of the handle actually broke off the screw)
After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back into place and then replaced the screws.
Parts Used:
-
Jennifer from Seymour, TN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
panel door was cracked
First I removed the 2 screws holding the panel on. I then removed the cracked panel. It was held in place by small "catches" built on to thew door. Replacing the new panel was easy, except, I forgot to attach the old handle. I was afraid I would break the new door but it came off with some prying. After replacing the handle, the door went on easily.
Parts Used:
-
Charles from San Diego, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
smoke alarm went off while frying
both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.
Parts Used:
-
Alma from Florence, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Panel Was Cracked
Removed 3 screws on end of door panel and used a putty knife to separate door panel from door. Replaced with new panel and reinstaled screws. Very easy!
Parts Used:
-
GARY from PALM COAST, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke rotating plate, it fell off counter after being washed
Opened door and put new plate in.
Placed order on Thursday evening and received Sat Am
Placed order on Thursday evening and received Sat Am
Parts Used:
-
Lois P from Morris, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
On-door water/ice dispenser lights failed, paddles did not work to dispense
It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!
Parts Used:
-
SM from JAMESTOWN, RI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the wheels came off
Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul
New one, ring that is. It was easy using the part from parts select
Thanks
Paul
Parts Used:
-
Paul from EXETER, NH
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Very Pleased with Parts Select replacement parts
Parts Used:
-
Edward from CENTENNIAL, CO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle discintegrated
Had left the small break in the handle go too long, There fore the screw holes in the door had wallowed out. Had to put some small washers in to bridge the wallowed out screw hole. The ends of the handle had broken off on the end of the mounting screws, had to use pliers and the screwdriver to get the plastic mounts off. There was enough room for the washers so no additional adaptation was needed. It all went back together very easily.
Parts Used:
-
Stephen from ELIZABETH, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Parts Used:
-
Eldon from ORANGE, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Parts Used:
-
Jan from ELK GROVE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!