This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
This inner door glass is used in ranges. It creates a transparent heat barrier inside your oven door. For this installment, the only tool needed is a #2 Phillips screwdriver. To repair, first remove t...
$98.21
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$37.51
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
This bottle of non-abrasive cooktop cleaner breaks down and gets rid of the hardest baked-on stains and residue without causing any harm to your appliance. The bottle is 10 oz and does not require a l...
$17.76
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the ...
$59.64
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
The light cover lens in your oven is designed to protect the light bulb. If your light cover lens is damaged, you will need to replace it. This part is made of clear glass and is roughly 3 inches in d...
$64.44
In Stock
Order within the next 1 hr and 48 mins and your part ships today!
Questions And Answers for KGRT507GBL0
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I removed the oven door by lifting it off with the hinges. Disassembled the door parts one at time making sure I remember where I removed the screws until I am able to get to the broken glass. The most difficult part is making sure that the insulation strip & the gasket stayed in place after I replaced the broken glass & doing the reverse
... Read more process of installing the parts together. Relatively easy process as long as you remember where the parts go. When in doubt, I had to refer to the pictorial of the disassembled door shown on your website.
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It i
... Read mores available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Although the ignitors glowed brilliant yellow I learned from an expert there are 2 fail modes. 1. that they break and don't glow well enough to ignite the gas or 2. they get resistive over the years and do not pass enough current to open the valve. This is important to know because the current passes through the ignitor before it gets t
... Read moreo the valve. If the ignitor resists too much then the valve never gets enough power to open. As evidence you get slow ignitions until one day it stops altogether.
There are 2 ignitors in this oven. one for the broiler and 1 for the oven. The broiler is exposed so easily removed. For the oven you need to remove the flame spreader cover and the flame spreader. Need a good screw driver for all the screws in the oven because they get corroded from the hostile environment and also the factory torques them in pretty good when new. It is hard to get leverage leaning into an oven without leaning on the oven door which could unhinge it. With a good screw driver and getting a good seat into the screw you can break it loose. Then some muscle power to get it out. 1 screw refused to come out all the way so I grabbed it with some pliers and pulled and twisted it out. A trick I learned from my days as a mechanic is to use valve lapping compound on the screw driver. The diamond dust bites into the screw for a grip on those really bad ones.
The last tricky part is you have to remove the back cover on the oven, unplug the wires and pull the ignitor out through the oven. When you see the wires in the back you will see insulation packing. Hint: If your smart you will tie a string to the wires before you pull it though so it is easier to pull the new ignitor wires back the same way. Else you need to use a stick to feel your way through the insulation packing to find the wires.
Hardest part of this job is undoing the screws. The rest is easy.
