Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KGRC608LSS0 > Instructions

KGRC608LSS0 KitchenAid Range - Instructions

All installation instructions for KGRC608LSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KGRC608LSS0
46-60 of 134
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

left hinge had snapped, couldn't close door

  • Customer: Edward from Lower Gwynedd, PA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Unscrewed about 10 screws to disassemble the door to get at the hinge then screw new hinge in. Was inspired by the woman who said she did it while watching a child. I saved $200 in the repair fee I was quoted

Cracked inner door glass on self cleaning oven

  • Customer: John M from Ponte Vedra Beach, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
Pulled the oven door out. Took the whole door apart and put it back together. The first time I put it back together the inner glass was still loose so I had to take it apart again and figure out how to hold everything together tightly. Your part was perfect. The glass was exactly the same as two others in the oven door. I wish I had instructions but when the parts fit it sure helps.

Inner door glass cracked after cold water spilled onto the hot glass.

  • Customer: John from Natick, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
As others have said, the repair is easy and it's just a matter of unscrewing the screws (with a drill, not with a hand screwdriver) and carefully arranging the parts so you can reassemble in the same order. The trickiest part for me was removing the door. The flat metal part of the hinge extends straight back into the stove about four inches. You need to open the door a bit (about 45 degrees worked for me, but any angle where you feel you have leverage vis-a-vis the hinge will work) and then lift the door at the hinge slightly while pulling straight back. I was worried the hinge would spring out and cut my fingers off, so I kept my fingers away. As it turns out the hinges didn't snap down once the door was removed, so at least on my stove the hinges were not as scary as I imagined they could be. The whole process was a one-person job, though if you have two people, it would be nice to have one person on each side of the door while removing it and replacing it when done. All in all, it was definitely worth it in time and money to do this repair myself -- the oven was back up and working within a day of the broken glass, and I'm sure I couldn't have gotten it done any sooner had I called someone to repair it.

cracked inner door glass

  • Customer: ernest from coplay, PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
removed 4 scews underside of door 2 more at top to remove door handle. than removed front door panel. removed inner sheild by bending 4 tabs.removed outside door glass than insideglass. reversed process to complete.

I snapped a bolt on the main power terminal block when connecting the pigtail.

  • Customer: Frank from Palm Coast, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 6 people found this instruction helpful
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

We are living in a rental house. The oven was missing a rack, so I called and ordered one.

  • Customer: Pat from Royal Oak, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
I think this does not qualify as a repair. I called and ordered the oven rack, it came in the mail and I put it in the oven. Nothing to it.

Broken inner oven door glass

  • Customer: Terrence from Bloomingdale, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.

electrical short from oven light.

  • Customer: William H. from morehead city, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Inner door glass

  • Customer: william from POLK CITY, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.

REPLACE INNER GLASS ON OVEN DOOR on KITCHENAID SUPERBA RANGE

  • Customer: Robert from BURLINGTON, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.

Broken door inner glass

  • Customer: Louis from RIVERHEAD, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Video's did not show my door construction so I had some difficulty and surprises. One must disassemble and keep all parts in order of disaasembly with all screws for each part.separated. Be methodical and patient and it will all work out.

Glass cover broken and gasket needed replacement in oven.

  • Customer: Sandra from WOODBRIDGE, VA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Removed broken glass cover and bulb, cleaned old gasket off with damp cloth and replaced with new bulb, glass cover and gasket. No tools needed.

Clearly, the bulb was the problem. The gasket is an invitation to more trouble.

  • Customer: James from THE VILLAGES, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Simple. But beware changing just the bulb when the gasket is not secure.

Purchased home but stove had no broiler pan.

  • Customer: Raymond from BLOOMINGTON, MN
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Purchased 2 piece broiler pan from this site

Oven temp not correct.

  • Customer: Alex from ORLANDO, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
4 screws in the back removed the back plate. About two thirds of the way up, on the left hand side, there is a single screw that is holding in the sensor. Easily removed the screw and unplugged the sensor. Reverse the sequence to put everything back. The only issue is it's not the easiest to get the back plate back on. Be patient and you'll be fine.
All Instructions for the KGRC608LSS0
46-60 of 134