KEBC278KBT02 KitchenAid Wall Oven - Instructions

Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.

First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.

This repair would have cost $164 through A&E factory service.

The first thing I did was to remove the oven door by releasing the two latches on the hinges (by hand). I then raised the door toward the vertical position and lifted up. The hinges slide out of the oven housing. I laid the door, inside face up on my island counter top. This ensures that none of the parts will fall when disassembling the door. Next I unscrewed the screws 4 top and bottom and four on the inside face. This releases the frame from the front housing. Lift the frame off the door, exposing the glass pieces. Lift off the broken inside glass and place the new piece in the glass retaining housing. Replace the outside frame and replace all screws. Take door back over to oven and slide hinge bottoms back into slots on oven. Rotate to horizontal position and flip latches back to locked position. Total time was about 10 minutes mainly because I was curious how the door was constructed and I poked around while it was disassembled.

My wife used the self cleaning function for the first time after 1.5 years of owning, of course out of warranty. A quick google search identified the problem. Called Kitchenaid, they said of course it can't be that simple, they had never heard of this problem, need to schedule a service call. Googled and found this site, Ordered the part, came in, only took a screwdriver and about 20 minutes, just like all the other posts.

shame on Kitchenaid for not owning up to the problem. I even e-mailed them all the links, they did not acknowledge them.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Safety first , I shut off the circuit breaker . I removed the racks from inside the wall oven . I removed the the wall oven from the niche .Then removed the three sheet metal panels in the rear of the oven exposing the mounting screws that hold the blower down .I removed the wires from the blower motor and then the blower assembly ,then I removed the small duct affixed to the blower assembly by a single sheet metal screw and transferred it to the new blower assembly . I installed the adhesive backed foam strip that is a vibration dampener and reassembled in reverse order.Once the over was returned to its original position in the wall mounting I turned the breakers back on and tested the oven ...AAAAAAAAA++++++++++++ To be fair i must admit that I am not a novice at this 15 years of my working career revolved around HVAC and appliance repair ,still however a novice that is mechanically inclined can perform the same task in about 70 to 80 minutes as opposed to my 35 . That is all there is to it.

There are two lights in this model oven. The glass will open by pulling outward on the near end. Since these are halogen bulbs I used a clean cloth to hold the bulb while replacing. Bulbs are expensive especially when purchased from Kitchen Aid dealer. I got two bulbs from PartsSelect delivered in two days for considerably less.

My husband did the repair and said it was very easy to do with the following instructions that I got from the Fix Ya website.

This is a design flaw in the Kitchenaid convection ovens. I can help fix this problem if you have a built in oven (I don't know if the parts are located in the same place for stand alone ovens). First it is not a FUSE that has blown rather it is the thermostat in the rear of the oven. (Part #4452223) This small part cost about $37 US and after shipping it will cost you about $47. I tried to get an estimate from an electrician as to what of frustration I decided to tackle the problem mthey would charge for the part and to come out and fix the oven an the price was about $90 for the part and anywhere between $100 and $170 more for the service call + repair! After a day myself.

The very first thing you must do is shut off the circuit breaker to the oven and put a very large sign on the panel that reads DO NOT TOUCH! That is 220 volts to that oven and while most panels have just the oven ont circuit you dont want anyone reactivating that circuit by mistake!

The next part requires a little work. Find the side panel screws (usually located in the oven door) and remove the two panel flanges that cover the 2 or 4 mounting screws that keep the oven in the wall. Now go underneath the oven and find the power junction box, take off the cover and disconnect the wires that run from the oven. Remember which goes where. Next remove the little nut that holds the electical conduit cable to the junction box then loosen the wires. Once this is done you can now slide the oven out and get to the thermostat.

This part requires a little elbow grease. Find a platform or table that fits just under where the stove will slide out and slide the oven on top of the table or whatever for support. In the back of the oven there will be a sheet metal panel that covers the thermostat and other wires, remove the 5 or 6 screws that hold this panel on and put the panel aside. Almost in the middle of the oven's back you will see a little black device with two wires running out of it (one red the other white or yellow). It will have the part number on its front, remove the wire and notice that the thermostat is half red and half white (remember this for the new part will have the same markings) the red wire goes onto the lead coming from the red markings. When you have the new part simply put the new one in (remember: the red side to the red wire), attach it to the back of the oven, replace the sheet metal cover and slide the oven back into place securing it with the screws. Viola! you are done! Turn on the power and then test the oven (I used the broil setting to warm it up then switch to a temperature setting). The entire process took me about an hour and I am NOT a handyman!

Removed a screw and clip to remove the lens and replaced bulb. Then replaced clip and screw. Done.

First, I removed the grill from the top of the microwave by removing 3 screws and then by sliding it out. It was a bit tricky, but you have to rotate it under so the grill comes out from behind the display.
Next, I removed the bottom grill by removing 4 screws. This one removed easily. Then, I removed 2 more screws that were under the bottom grill and was able to start sliding out the microwave unit.
I was only able to pull the microwave half way out because some wires were stopping me from pulling it out more. I removed the big square piece of insulation and had enough room to get to the light assembly.
I removed the retaining clips by pushing the right side of the clips to the little opening in the middle on the right hand side. Then I was able to remove the light bulb and replace with the new one.

Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

Very easy once we figured out how to remove the oven door - which was insert the Allen keys in the holes in the hinges and pull the door out. We thought there was some way of using the Allen key to undo a pin or bolt but it was as simple as putting it through the hole in the hinge !!!!!

Don't, Don't, Don't!!!!!!! call a repair man to replace the thermo fuse. If you are able to use the T.V. remote and crack a twist top off a cold beer, then you can DO this. I am 47 years old and half retarded and my 84 year old neighbor and I completed this task in 12 minutes. Turn off the breaker panel, pull the oven out, (it is hard wired). We placed it on a 4 wheeled dolly. Unscrew 11 screws, pop the panel. The fusee is at the top/center with two screws holding it. Pull the two wires off, screw it back in place. Put back the panel & 11 screws. Put the oven back in place. Turn on the breaker and you are done. PS Tell your wife or girl friend this might take an hour or so. Send her to the store for a six pack & steak.

Used flat tip screw driver to pry front clip holding glass cover out of position. Pulled out dead bulb and pushed in new one. Slid clip back on glass cover and slid back into place. Simple. .

Once I figured out to get the door off, the actual replacement went well.
remove door, using allen wrenches in the holes of the door
remove outer glass - two screws on top, four screws along sides of inside door, two brackets on the bottom
that revealed anothe sheet of glass- held into place by a metal flange at the top (3 screws) and two brackets at the bottom. Pay close attention to how they are mounted for reassembly. They are the same physical configuration, but mount differently to hold glass up from the surface below
That reveals another sheet of glass held into place by two "ears" at the top and a bracket at the bottom.
When that is removed, the next thing to come off is a metal housing on which the glass just removed was mounted. I elected to leave the door hinge springs in place, and slide the metal housing in and out of position. That reveals the glass which needed replacement.
There is some insulation around the glass, but under the metal housing. It came out when I slid the metal out, which moved it from its location, but I think I got it back ok...be sure that it does not sitck out around the glass when you reassemble everything. Put everything back in place, replace the door and remove the allen wrenches. Done. Parts select had the product, and sent it very quickly.

Ordered the glass and read the other reviews/instructions on the PartSelect site. Also read the instructions in my owner's manual for removing the oven door. The hardest part of replacing the glass was the removal and replacement of the door. Once I had the door out, replacing the glass was as simple as removing about 8 or so screws, lifting off the cover and replacing the glass, then replacing the screws. One of the hinges on the door had closed and I was not able to open it to replace the door, so I had to have a neighbor come over to over his muscle power. The hinge problem should not have happened and without that little issue, this is a simple repair that I'm sure saved me at least $100.00 on repairman! And - I'm a woman!