Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KEBC208KSS02 > Instructions

KEBC208KSS02 KitchenAid Wall Oven - Instructions

All installation instructions for KEBC208KSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEBC208KSS02
61-75 of 142
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Inner glass door shattered

  • Customer: Michael from LAKE FOREST, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Inner glass was broken by previous tenants

  • Customer: Janene from ORLANDO, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Read all the way through this once before doing it. It really helps in keeping pieces and parts separated. First I had to take off the oven door. Please do this as it will make your life so much easier! The owners instructions does a lousy job explaining how to do this. You need to insert a small Allen wrench into the holes behind the door hinge pin. Just stick them in there and leave them. If you don't have Allen wrenches you can use small nails or the like, but you have to put something into the holes. Close the door slowly, yes it will feel like you are going to break the hinges or the wrenches. When you get the door almost completely closed you should wiggle the door a bit by the handle and pull up. The door will come off. Once you get the door off you can get to work. Leave these wrenches in the hinge holes. You will need a flat surface big enough to lay the door down to work on it. Lay it down with the handle towards the surface and the broken glass facing you. Remove the 4 screws on the broken glass side, the 2 screws holding the brackets on the bottom and the 2 screws on the top of the door. You will need to wiggle the inside cover off because there are 2 little clips at the top you need to get it off of the outer glass door. You should have 2 separate pieces, the outer glass of the door and the inner tempered glass and sheet metal portion of the door. Set the outer glass door aside, somewhere safe, as you really don't want to have to reorder that part too! From there you can lay the door down with the broken inner door glass towards the work surface. Remove the screws and good pieces of glass and lay them down in the order you take them out. This helps putting them back together later. Keep the pieces together in sets so you know which set goes to each section. There should be 3 pieces of glass total in the assembly. You remove the screws and the 2 good pieces of glass. The inside door glass is accessible under a large piece of sheet metal held in place by little flanges cut into it. You can remove this sheet metal panel piece by wiggling it out away from under the hinges and away from the hinge end. There is a piece of insulation under there as well. Make sure you reseat it correctly when you put it all back together. If you don't it will stick out, and make things hard to line up. Pull the broken glass out, Put the new glass in and replace the sheet metal panel. At this point I would suggest putting the four screws you took out at the very beginning from the inside of the door back in. They keep the 2 hinge assemblies in place and they will be harder to line up if you don't. You need to work from the bottom side up but it's pretty easy to get the 4 screws back in. Don't be afraid to wiggle the pieces around so you can line up the holes. They need to line up so that the hinges line up back to the oven. Reverse how you took the other glass pieces out and put the door back together. Put the front glass piece back on and secure it in place with the bottom door brackets and screws and the top 2 screws. Lift the door unit back up by the handle and place it in the slots for the hinges exactly the way you removed it. You will feel it sort of catch when you pull the door open slowly. Remove the Allen wrenches and you are done.

Inside oven door glass was broken and door was not closing completely.

  • Customer: William from Dumfries, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the door from the oven by locking the hinges with the built-in locks leaving the door open about 20 degrees. the door can then be lifted slightly off the hinges and pulled out at the bottom while tilting the top inward to remove it from the oven. With the door laying on a suitable surface with the outside face down, I removed about 6 or 8 screws from the door inside panel freeing the springs and the inside panel from the middle and front panels. Care must be taken to note from which locations the pointed self-taping screws come as opposed to the narrower-thread machine screws that hold the springs. Note: The inside panel does not need to be removed! Once the inside panel is freed from the inner panels, using suction cups the glass can be lifted slightly and slid toward the bottom of the door, rotated slightly, and removed through the window hole in the back face of the door. The new glass is installed in a similar way using suction cups by maneuvering it at a angle through window hole and into its frame. The hinges were replaced by lifting the bottom of the inner door panel slightly to clear the hinge and swapping in the new ones. Be sure to observe the difference between the left and right hinges in the location of the screw hole at the bottom of each hinge The narrow-thread machine screws that hold the hinges to the inside panel should be installed first while you can get you hand inside the door to hold each hinge in alignment with the screw holes while you start each screw. Re-install the pointed self tapping screws by pressing down on the rear panel to collapse the spring-action glass frames within the door so that the short screws will reach their threaded hole. Be careful to back off the self tapping screws first until you feel a click into the original threads to avoid stripping the holes. Last re-install the door on the oven. The replacement hinges should have come with the springs already "cocked" with the built in locks in place. Install the door with it in tan almost-closed position by sliding the hinge extensions into the slots in the oven. Once the extensions are properly in the slots the door can be fully opened and the built-in hinge locks re-positioned to the unlocked position to allow the door to fully close. Should you accidentally release only one of the hinge locks in trying to insert the hinge extensions into the slots you will have to reset the hinge. If the door is free from the oven, this may require a pair of heavy pliers, like channel lock pliers, to re-tension the hinge spring and "cock" the hinge extension by re-positioning the built-in lock in the locked position. If the hinge lock on one side of the door releases, but the the opposite side hinge extension is not fully inserted into the oven slot I recommend carefully moving the door to the fully open position, being careful to avoid twisting the inserted spring's extension, so that the hinge lock can be re-positioned to the locked position, the door full removed, and start again to install it. It helps to have two persons to hold opposite sides of the door for this operation as the door is heavy, but not essential. When in the proper position the hinge extensions may not appear fully inserted, but this is normal to allow for closing of the built in locks. It helps to observe how much of the hinge extension is exposed either before removing the door initially, or, if you have a double oven, looking at the hinges on the door of the other oven. Good luck with your repair.

oven light would not come on

  • Customer: david from SOUTHAVEN, MS
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner

I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.

  • Customer: Karen from Oklahoma City, OK
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

inner glass broken

  • Customer: J from Niceville, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
fairly easy. took a while to reassemble. otherwise all was ok.

wife broke inside glass, cooking no less...

  • Customer: Dennis from Rowlett, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
removed door, took out 8-9 screws, slid door upward, and removed. took out broken glass, and replaced.

Inside oven glassed cracked.

  • Customer: Kimberley from Gilberts, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First I removed the door from the double oven as instructed in the owner's manual. Then I removed the screws holding the door together. I removed the layers necessary to get to the inner door glass. Then reassemled it in the order that I had taken it apart. A total of 15 screws. My tip would be pay close attention to how you disassemble.
Not only did we save the cost of a repairman but because of Part Select we got the glass for less than half the price quoted to us from Kitchen Aid for the part and delivery.
Very satisfied with our experience with Parts Select

Missing Retainer and screw

  • Customer: Jan from Edmond, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 11 people found this instruction helpful
Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan

Block broke

  • Customer: Edward from Crimora, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Broken Door Glass

  • Customer: Chris from China Spring, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Removed Door, Took Door apart, Replaced glass, re-installed door. Pretty basic

Cracked my inner glass on my stove

  • Customer: lee from charlotte, NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Repair was very easy, Alittle time consuming. Unscrewed the outer skin of the door and removed the pieces.

broken inside glass

  • Customer: Rene from Keller, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced

inner glass broke (water on hot glass, not good)

  • Customer: eugene from Roseville, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I did not take the door off the oven, i dissassbled it in place. all the visible screws on the door have to be removed. The "vent" air diflector or what ever it is , between the upper and lower doors has to come off also to access the screws that hold the front of the door on. The only confussion i had was the bracket that holds the third layer of glass. I forgot that it is held on with the same bracket/screws that hold the secound layer on.

The interior oven door glass was broken

  • Customer: Dante from Apex, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I found some of the feedback posted on this site very helpful. Taking photos as I went along was also very helpful in remembering how to put it back together. There are several over-lapping pieces to the door and you have to be careful to put things back together in the correct order. Lining up the screw holes on the hinges with the door is also a little tricky.
All Instructions for the KEBC208KSS02
61-75 of 142