KEBC206KWH03 KitchenAid Wall Oven - Instructions

Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!

Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.

First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.

This repair would have cost $164 through A&E factory service.

Removed the oven door by following the straightforward instructions in the user's manual. Removed philips head screws to take the door assembly apart. Removed clips holding the two inner door glass plates, and the two plates. Removed the clamp holding the broken glass plate, then the glass and associated glass fragments. Then cleaned and re-installed the three glass plates and their clamps in reverse order. Re-assembled the door and re-attached to the oven. Only cautionary note is to be careful when removing, handling and re-installing the various glass plates. Watch out for fragments from the broken plate; they can cut you and/or fall on the floor.

My wife used the self cleaning function for the first time after 1.5 years of owning, of course out of warranty. A quick google search identified the problem. Called Kitchenaid, they said of course it can't be that simple, they had never heard of this problem, need to schedule a service call. Googled and found this site, Ordered the part, came in, only took a screwdriver and about 20 minutes, just like all the other posts.

shame on Kitchenaid for not owning up to the problem. I even e-mailed them all the links, they did not acknowledge them.

Important note: hinges are left and right do not mix them up or door will not re-assemble properly and you'll get to do it twice.

Steps I took:

Removed the oven door per the instructions in the oven operator manual. Removed several screws to release the interior steel liner.

Removing the steel liner was a bit of a hassle, Had to manipulate it to get it loose but it eventually came away from the stainless steel exterior door panel.

Disassembled the interior glass layers, there are three. The glass you need to replace is the last layer, of course. removed and discarded the broken glass. Note: the interior glass is not secured by a bracket or screws, it is held in place by compression of the interior steel liner and a another liner that is inside the door assembly (you'll figure this out when you dis-assemble).

Another note: there is a fluffy material gasket between these two liners, use care when you disassemble or the fluffy gasket will turn into confetti.

Take the opportunity to clean all glass and parts of the accumulated oven grease.

Re-assembled door and re-installed...looks good.

Another note, getting the door back together requires a little patience because there are clamping overlaps of the steel liner to the SS exterior door panel. Be prepared to jockey things around a little and make sure all your screw holes are all lined up before you begin to button it up. Remember, hinges are left and right they are not interchangeable.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Unfortunately, you must replace the whole door. It was only a matter of removing 6 screws but sliding the door back on was a little tricky. Still, it beat calling a repair man and the item came in 3 business days. The part fit exactly right.

Safety first , I shut off the circuit breaker . I removed the racks from inside the wall oven . I removed the the wall oven from the niche .Then removed the three sheet metal panels in the rear of the oven exposing the mounting screws that hold the blower down .I removed the wires from the blower motor and then the blower assembly ,then I removed the small duct affixed to the blower assembly by a single sheet metal screw and transferred it to the new blower assembly . I installed the adhesive backed foam strip that is a vibration dampener and reassembled in reverse order.Once the over was returned to its original position in the wall mounting I turned the breakers back on and tested the oven ...AAAAAAAAA++++++++++++ To be fair i must admit that I am not a novice at this 15 years of my working career revolved around HVAC and appliance repair ,still however a novice that is mechanically inclined can perform the same task in about 70 to 80 minutes as opposed to my 35 . That is all there is to it.

There are two lights in this model oven. The glass will open by pulling outward on the near end. Since these are halogen bulbs I used a clean cloth to hold the bulb while replacing. Bulbs are expensive especially when purchased from Kitchen Aid dealer. I got two bulbs from PartsSelect delivered in two days for considerably less.

My husband did the repair and said it was very easy to do with the following instructions that I got from the Fix Ya website.

This is a design flaw in the Kitchenaid convection ovens. I can help fix this problem if you have a built in oven (I don't know if the parts are located in the same place for stand alone ovens). First it is not a FUSE that has blown rather it is the thermostat in the rear of the oven. (Part #4452223) This small part cost about $37 US and after shipping it will cost you about $47. I tried to get an estimate from an electrician as to what of frustration I decided to tackle the problem mthey would charge for the part and to come out and fix the oven an the price was about $90 for the part and anywhere between $100 and $170 more for the service call + repair! After a day myself.

The very first thing you must do is shut off the circuit breaker to the oven and put a very large sign on the panel that reads DO NOT TOUCH! That is 220 volts to that oven and while most panels have just the oven ont circuit you dont want anyone reactivating that circuit by mistake!

The next part requires a little work. Find the side panel screws (usually located in the oven door) and remove the two panel flanges that cover the 2 or 4 mounting screws that keep the oven in the wall. Now go underneath the oven and find the power junction box, take off the cover and disconnect the wires that run from the oven. Remember which goes where. Next remove the little nut that holds the electical conduit cable to the junction box then loosen the wires. Once this is done you can now slide the oven out and get to the thermostat.

This part requires a little elbow grease. Find a platform or table that fits just under where the stove will slide out and slide the oven on top of the table or whatever for support. In the back of the oven there will be a sheet metal panel that covers the thermostat and other wires, remove the 5 or 6 screws that hold this panel on and put the panel aside. Almost in the middle of the oven's back you will see a little black device with two wires running out of it (one red the other white or yellow). It will have the part number on its front, remove the wire and notice that the thermostat is half red and half white (remember this for the new part will have the same markings) the red wire goes onto the lead coming from the red markings. When you have the new part simply put the new one in (remember: the red side to the red wire), attach it to the back of the oven, replace the sheet metal cover and slide the oven back into place securing it with the screws. Viola! you are done! Turn on the power and then test the oven (I used the broil setting to warm it up then switch to a temperature setting). The entire process took me about an hour and I am NOT a handyman!

Removed a screw and clip to remove the lens and replaced bulb. Then replaced clip and screw. Done.

First, I removed the grill from the top of the microwave by removing 3 screws and then by sliding it out. It was a bit tricky, but you have to rotate it under so the grill comes out from behind the display.
Next, I removed the bottom grill by removing 4 screws. This one removed easily. Then, I removed 2 more screws that were under the bottom grill and was able to start sliding out the microwave unit.
I was only able to pull the microwave half way out because some wires were stopping me from pulling it out more. I removed the big square piece of insulation and had enough room to get to the light assembly.
I removed the retaining clips by pushing the right side of the clips to the little opening in the middle on the right hand side. Then I was able to remove the light bulb and replace with the new one.

Easy, pulled out the old dis-colored racks and slid the new ones in. I was VERY happy with the quick receipt of my order. If I ever need parts again,this is where I will go

The repair is straight forward. The only complication anyone seems to be having is removing the door ( which is a definate must to do this repair properly). So I would like to add some details about removing the door. The manuel shows the allen wrenches going into what looks like the hinge itself to release it from the oven. This is not the case. The holes that the 5/32 allen wrenches go into are actually behind the hinge itself. I wrapped the allen wrenches with some painter tape to protect the surface of the door and oven from scratching. Then, simply insert the short end of the allen wrenches, one on each side, into the holes behind the hinge. Then as it shows in the manuel, gently close the door. But not all the way. As you get about 80% closed you'll feel resistence. That is the time to grasp the bottom of the door and start to lift it from the bottom, while stablizing it with the other hand holding the handle on the door. The hinge will start to release from the oven as you continue to press it closer to being all the way closed. The hinges will release if you are doing this correctly before the door can be all the way closed.

Hope that helps. Otherwise, once the door is off. Unscrew all the screws...pay special attention to what you are unscrewing and how it all fits together, because you're going to have to put it all back together again. Some of the glass is held in place with clips and some of it is not. Just lay it down flat and be careful to not force anything in or out and you'll find it quite easy.

I removed the bottom gasket retainer , single screw, with a screwdriver. The old gasket just pulls away. I cleaned the area under the old gasket with soap and water. I installed the new gasket whcih easily slips in place with the already installed retainer wires into the pre drilled holes.

Viola. Lokks like new.