KEBC147KWH0 KitchenAid Wall Oven - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

My electric oven is a built-in. First I turned off power to the oven.

Then, I removed the oven door as instructed by Kitchenaid, next I removed the screws that held the concealing-sleeves on each side of the oven opening. Slid down the sleeves, loosened the exposed screws on each to allow the oven to slide out. Slid the oven out abut half way to expose the top. Removed the metal sheeting from top of oven to expose area where door latch assembly was secured. Removing the sheeting was made easier by removing the screws on each side of the control panel and lifting the panel out of the way.

The latch assembly is held in place by two screws through the front of the plastic venting. Identified the connections to appropriate points before I removed the wiring, removed wiring and attached to points on the new latch assembly.

Secured latch assembly to plastic vent, secured sheeting to top of oven, placed conrol panel back in place, pushed oven back and secured with screws.
Slid sleeves into position, secured with screws and replaced oven door.

Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and connector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner

1- TURN OFF POWER TO OVEN
2- REMOVE OVEN
3- REMOVE BACK PANEL SHROUDING
4- DISCONNECT POWER TO BLOWER
5- REMOVE BLOWER UNIT
5- REPLACE WITH NEW UNIT
6- RECONNECTED POWER
7- PUT OVEN BACK

First I cut off power ! 2 screws for oven trim,4 more to disconnect from cabinet. Hardest part was pulling oven out and pushing back in. I found a big box of correct size to rest it on so I didn't need to disconnect the powerline. 8 more screws to remove the back panel. 2 screws to remove the thermostat.Then put it back together. New part had arrived sooner than expected, cost of the part was less than a minimum service call would have been! I absolutly will use your site again.PS Wife was amazed and now thinks I'm a genious.

I first did a search with my issue, found out there were many others with the same issue. That then led me to see the part, a fuse / thermostat, was the culprit and easy to replace it seemed. But first called a service co. who confirmed my findings, and quoted a fix of a $2-300! So I bought the part; worse case I'd have someone else install. The web site noted the few screws to remove and a key suggestion to find a box of same height to easily slide out oven; I used a porter cable nail gun case which worked great. Took my time removing trim, mounting screws etc., slid out oven easy. Removed back plate and there was the older one. Removed and installed new in a minute. Spent more time cleaning around trim than actual install. What a great day it was. Wife was happy too!

Shut off power at breaker and removed oven door to lessen weight. Removed oven trim and retaining screws and tried pulling out of cabinet. Stuck on power cable, so had to remove Mircrowave oven above to get to power cable plug. Removed oven back cover panel to access thermostat. Easy to unplug and replace with new thermostat. Reassembled and turned on power. Cooked dinner in oven.

I removed the two stainless trim pieces (2 screws) and then two screws which hold the oven frame to the cabinet. Be careful to put a pad on your floor before you pull the oven out of the cabinet as there are sharp edges on the bottom of the oven. I removed apprximately 12 screws holding the back panel in place. The fixed set point thermostat is in middle toward the top of the oven cavity after removing the rear panel. Just remove two screws and slide the terminal connectors onto the new thermostat. Very easy job for someone who is not too handy.

Repair was fairly simple, unscrewed oven from cabinet and pulled it out. Then remove screws on back panel to access the thermostat location. Unscrew old thermostat, unplug it from connectors and plug in new thermostat. Then screw back in place, replace cover and pop oven back in place. Now fire it up, worked for me! Thanks to part-select. Good luck everyone. Probably saved $200 service call.

GENERAL APPROACH:
1) Checked YouTube for some general guidance: VERY helpful things there for this! PartSelect's install info. was helpful as well- Thank you for this!
2) had table set up in order to disassemble the door once it was removed
3) There are 4 separate glass panes in there- they all need to be cleaned
4) TOOK PICTURES AND MADE CAREFUL NOTES AS (12 or 15?) SCREWS ARE TINY & THERE ARE DIFFERENT TYPES. TAPED THEM NEAR WHERE I REMOVED THEM SO AS TO KEEP THINGS STRAIGHT
5) Like any project little or big, just take your time & it actually works out well
6) take advantage of this downtime to clean the oven good, as well as the door & panes of glass. Cleaning was 75% of this project.
7) EXTRA: If you're so inclined, turn the breaker off for the Oven & carefully remove the lower heating element to enable easier & more thorough cleaning of your oven. You'll be glad you did this- and so will your cook!

Sorry but that would take too long to give all instructions, but I will mention that there were four glass plates if you count the cover of the door which is a large glass piece. All glass plates had to be taken out or off including the holder hardware in order to get to the inner glass (about 15 screws in all). No you-tube videos seemed to apply directly for this door. Taking some pics and using a card to hold screws in the pattern they were taken out helped keep the in order to be replaced (I screwed the screws into a paper sheet to keep the pattern with some labeling like top, bottom, etc). Lower glass door appears to only have two glass plates (didn't take it apart, but inner glass holders were not seen when peering in through the inner glass as they are in the upper door). If the inner glass plate on this door gets broken it should be easier. The glass was broken for some time before this repair so there was a lot of cleaning required inside the door. Oh, by the way, when taking out the door off pull out (not up) after locks are released and when the door is mostly closed. Push back in and open door down a bit to lock back in place. This is far from complete but I hope it helps some.

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.