Models > KEBC107KSS05 > Instructions

KEBC107KSS05 KitchenAid Wall Oven - Instructions

All Instructions for the KEBC107KSS05
31 - 45 of 116
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken inside view glass
Removed 4 screws top and bottom of the outer door panel. Remove outer door, then the two inner panes of glass. You are then able to remove the broken inner glass. Carefully slide the new inner glass into place, being careful not to tear the insulation. Once new inner glass is in place carefully replace the two inner glass panes and secure the screws. Replace the outer door and the top and bottom screws and that's it!
Parts Used:
Inner Door Glass
  • Michael from Costa Mesa, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke the inside oven door glass while cleaning it
The exact part for this oven is no longer available. I purchased one hat was close in size, but larger than the original. Upper and lower brackets hold the glass in place, so length was not a problem but height was. I removed the upper brackets, re-shaped them with the vise, a hammer and metal shears. The glass would now sit inside the bracket where the screws also went. I had to be quite careful the screws did not shatter the new glass.

The hardest part was aligning the 4 holes for the top brackets. Since 2 holes were on one piece of the door, and 2 were on the other (holding the glass sandwiched between) precision was critical. Also the screw length was critical because the glass now sat in a area where it could come in contact with the screws. (I know - pictures would be most helpful, and I didn't take any.)

Using tape and lots of patience, I got the holes aligned. I covered the old holes inside the oven door with spare screws. I filed down the points of the sheet metal screws so that, if they contacted the glass, they would not be pointed.

Once everything was reassembled, I turned the oven on high for about 1/2 hour to ensure the heated metal and glass all played nicely together. We've had no problems in the month since the repair.
Parts Used:
Inner Door Glass
  • Guy from Little Rock, AR
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inner glass to oven door shattered
Removed the 6 screws securing the door and inner frame unit. Lifted off the frame and inner glass unit. Then, after cleaning all the broken glass, put the new glass in; first reattaching the inner frame and then the outer door cover.
Parts Used:
Inner Door Glass
  • Robert from Forsyth, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Parts Used:
Main Power Terminal Block
  • Dana from Black Mountain, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing inner glass on oven door
The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.
Parts Used:
Inner Door Glass
  • Kel from Denver, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked inner door glass on oven
I am not the handiest guy around so i was a little nervous doing this job but figured i would take a crack at it ( no pun intended). Took the door off as per instructions from kitchenaid , unscrewed all the outer screws , took off the back of door unscrewed the metal bar holding the glass in ( there are 3 levels of glass) took the 2 good glass sheets out got to the broken glass removed that put the new one in , replaced all the other glass and screws and put door back on, and i felt so proud. Probably saved about 150 dollars by doing it myself. I feel so proud.
Parts Used:
Inner Door Glass
  • Thomas from Rockville Centre, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Taking the door apart.
This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.
Parts Used:
Inner Door Glass
  • R G from Orlando, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
After selfclean cycle, oven stopped getting warm
First I cut off power ! 2 screws for oven trim,4 more to disconnect from cabinet. Hardest part was pulling oven out and pushing back in. I found a big box of correct size to rest it on so I didn't need to disconnect the powerline. 8 more screws to remove the back panel. 2 screws to remove the thermostat.Then put it back together. New part had arrived sooner than expected, cost of the part was less than a minimum service call would have been! I absolutly will use your site again.PS Wife was amazed and now thinks I'm a genious.
Parts Used:
Range High-Limit Thermostat
  • edward dennis from cocoa, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't heat after a cleaning cycle run
I first did a search with my issue, found out there were many others with the same issue. That then led me to see the part, a fuse / thermostat, was the culprit and easy to replace it seemed. But first called a service co. who confirmed my findings, and quoted a fix of a $2-300! So I bought the part; worse case I'd have someone else install. The web site noted the few screws to remove and a key suggestion to find a box of same height to easily slide out oven; I used a porter cable nail gun case which worked great. Took my time removing trim, mounting screws etc., slid out oven easy. Removed back plate and there was the older one. Removed and installed new in a minute. Spent more time cleaning around trim than actual install. What a great day it was. Wife was happy too!
Parts Used:
Range High-Limit Thermostat
  • carlos from Holtsville, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven light would not come on
cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner
Parts Used:
Lights Transformer - 60Hz
  • david from SOUTHAVEN, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't heat after running self cleaning cycle
I removed the two stainless trim pieces (2 screws) and then two screws which hold the oven frame to the cabinet. Be careful to put a pad on your floor before you pull the oven out of the cabinet as there are sharp edges on the bottom of the oven. I removed apprximately 12 screws holding the back panel in place. The fixed set point thermostat is in middle toward the top of the oven cavity after removing the rear panel. Just remove two screws and slide the terminal connectors onto the new thermostat. Very easy job for someone who is not too handy.
Parts Used:
Range High-Limit Thermostat
  • Jerry from Lebanon, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wall-Oven not working after self-cleaning
Shut off power at breaker and removed oven door to lessen weight. Removed oven trim and retaining screws and tried pulling out of cabinet. Stuck on power cable, so had to remove Mircrowave oven above to get to power cable plug. Removed oven back cover panel to access thermostat. Easy to unplug and replace with new thermostat. Reassembled and turned on power. Cooked dinner in oven.
Parts Used:
Range High-Limit Thermostat
  • Jim from San Antonio, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not heat up, after self cleaning
Repair was fairly simple, unscrewed oven from cabinet and pulled it out. Then remove screws on back panel to access the thermostat location. Unscrew old thermostat, unplug it from connectors and plug in new thermostat. Then screw back in place, replace cover and pop oven back in place. Now fire it up, worked for me! Thanks to part-select. Good luck everyone. Probably saved $200 service call.
Parts Used:
Range High-Limit Thermostat
  • Richard from Chicago, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Inner Glass on Oven Door by a Grandmother Who Should Know Better!
After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.
Parts Used:
Inner Door Glass
  • Diane from Citrus Heights, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was an annoying buzzing sound coming from the bottom of the stove
I pinpointed the location of the sound, took off the protective plate, felt it vibrating against the plate. I disconnected the power supply, and looked at the wirings and how it was connected, saw some burning residue surrounding the area of the Transformer. Then figured that I could simply replace this. I wrote down the Model and Serial number of the Stove, searched online, found this site. Located the part on the diagram, then simply ordered it. My part arrived in 3 days, and had the part replaced the next day. Couldn't be a smoother fix. Thanks.
Parts Used:
Transformer Control
  • Craig from Snoqualmie, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KEBC107KSS05
31 - 45 of 116