Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kent
January 27, 2020
Where in the us or the world can i find a warehouse or supplier that may stock a light socket assembly for an 8 year old jenn air rangehood? Everywhere i’ve checked state that the part is no longer made nor available. Any information or possible leads on suppliers, appliance junkyards, etc you can provide would be deeply appreciated. Thank you very much for your time!Length pivonka
For model number JXT8836ADS
Hi Kent, thank you for your question. The part you are requesting on has been discontinued and we have no known replacement listed in our system. We have no further information. You are welcome to contact the manufacturer of the part to see if they have recently released a new substitute. You may still be able to locate the part you need by trying the following: 1. Using a search engine to type your part number and see if other retailers still have this part in stock. 2. Visiting online stores such as eBay and finding sellers that have this part. 3. Trying retailers and repair stores in your local area to see if they have the part in their inventory. 4. Talking to a local repair technician, who may have the part you need, or may be able to repair your existing part. This was the part number: 49001166. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
First attempt: Power off to hood. Removed the switch assembly thinking the problem was with the off/on button (two phillips screws and a gentle lift of the bracket to free the assembly). A sevice loop allowed me to lower the switch assembly and inspect the circuit board (CB) inside.
... Read more I tried to operate the switch directly on the CB (i.e. bypassing the button hoping it might be something mechanical with the button, but still could not turn the lights off. Believing the CB was bad, I ordered a new one.
Power off to hood. I installed the new CB but I still could not turn the hood lights off.
I then ordered the next higher assembly circuit board (looking at the PartsSelect.com drawing).
Second attempt: Received the new CB. Power off to the hood. Getting this CB down so that I could replace it was a problem, as it was higher up in the hood and was very space limited, and having to work upside down, looking up into the hood. I used a double ended phillips screwdrive with 90 deg bends on both ends for the four screws holding the cover on the housing with the CB inside. The screws were recessed in the cover. Once I got the head exposed, I used pliers to turn the screws out a bit faster. We're talking a quarter turn at a time here. Once the cover was off, I dopped the CB down using the service loop. I removed the old CB and installed the new one, carefully changing out each connection one at a time. This required the loosening of two very small terminal screws in a cconnection block mounted on the CB for the power lines .You need a very small good quality screwdriver that fits the screws good to get them loose, as they were very tight and it would be possible to damage the CB if you twisted the block on the board (be very careful here). There are also four other slip on connector and one multi-pinned connector (care required here also to avoid bending any of the very small pins). No soldering required. I tested the system with the CB dangling from the hood and everything worked. I put the CB back up in the housing, making sure the wires would not be pinched by the cover (which only goes on one way in order to "clamp" the wires in place), carefully put the cover in place, and put the four screws back in, I then tucked the service loop back up out of the way, and put the hood filters back in place.
Power back on and a final test.... All good.
One other thing. The CBs should be handled with care reqarding static discharge. Touching the hood and handling the boards by their edges is probably a good idea.
I hope this helps someone.
Thanks PartSelect. com
P.S. Any chance of returning the first CB which I didn't need?
I removed the face of the lower located plastic box. I wrote down a description of current wire locations so I could duplicate that with the new control board. The switch out required a head lamp and a strong, small flat screw driver. This screwdriver is not a common size, and needed to be stronger than the eyeglass screwdriver I initi
... Read moreally tried. Minus the time to borrow that screwdriver from a neighbor, the fix took about 10 mins. I was upset I've waited 6 mos. to attempt this simple fix.
Could not have been any easier thanks to INSTANT REPAIRMAN on PartSelect. The site indicated the electronic board was the problem in 99% of cases. The Maytag repairman had come by earlier indicating the problem could be fixed for $500 or we could have a new hood installed for $2500. Fortunately, I decided to give it a try myself. We order
... Read moreed the part as per the recommendation on this site, turned off the electricity, switched the electronic board with the new one taking care that all wires matched (actually drew a little diagram), and flipped the switch. It worked! 20 minute installation, personal gratification and $500 richer. Priceless! Thanks PartSelect and thanks Instant Repairman!!!