Models
>
JRSD245W
JRSD245W (9Q25A) Jenn-Air Refrigerator - Overview
Sections of the JRSD245W
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Egg Tray
PartSelect #: PS11743588
Manufacturer #: WP67004411
This egg tray holds fourteen eggs.
$11.14
In Stock
Door Hinge Washer
PartSelect #: PS2049932
Manufacturer #: 54233-1
This door hinge washer is used between the lower hinge pin and the lower hinge bushing.
No Longer Available
Washer
PartSelect #: PS11742796
Manufacturer #: WP52185-1
This door hinge washer is less than an inch in diameter. It is all white in color and it is made entirely of plastic.
$7.14
In Stock
BUSHING- L
PartSelect #: PS2064814
Manufacturer #: 66034-1
The bushing is made of white plastic and is for a 3/8-inch pin. This bushing is part of your refrigerator assembly and is found on the top of the door. A worn-out bushing will cause your door to becom...
$22.45
Special Order
Food Door Gasket (measures 20" by 60")
PartSelect #: PS2065500
Manufacturer #: 66929-14
This white fresh food door gasket measures approximately 20 inches by 60 inches. It is all white in color and is made of rubber. This gasket is used for the fresh food door of many side by side model refrigerators.
No Longer Available
Lower Hinge Pin
PartSelect #: PS2049401
Manufacturer #: 53672-1
This lower hinge pin is almost an inch long. It is made of metal.
No Longer Available
Questions And Answers for JRSD245W
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
One side of the dairy door broke right at the little tab site.
I have to say the packaging of the diary door was A+++ It took less than a minute to snap out the old door (that I had tried to hot glue) and snap in the new door. My story is what a fantastic sales department you have. I submitted my order for the dairy door as well as new shelving hinges. The hinges came in right away; however I rec
... Read more
eived an e-mail saying they no longer had the dairy door. I received a message on my cell phone that the sales lady She said she located a couple of dairy doors in other warehouses and was going to check their availability. Sure enought, it took a week or so, but she did come through with the dairy door for me. I was told they only had a couple left and that they were not making them any longer. Whoever this sales lady is.... three cheers for you what an excellent job. She really did not have to pursue the order any further than her own warehouse but she did - thank you for your excellent service!!!
Read less
Parts Used:
-
Deborah from Walker, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pantry Drawer Cover keeps falling off, not held in place by End Cap Kit
I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabine
... Read more
t on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.
Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.
Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.
Read less
Parts Used:
-
Gerald from TANEYTOWN, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!