Models > JMV8196AAB > Instructions

JMV8196AAB Jenn-Air Microwave - Instructions

All Instructions for the JMV8196AAB
31 - 45 of 77
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light bulb burned-out
screwed in new bulb
Parts Used:
Light Bulb - 40W
  • Pablo from Burlingame, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original rotater broke
Replaced the broken piece with the one purchased at Partselect.com. I was concerned that the part would not be correct since all we did was enter the model number of the microwave. PartSelect.com was really easy to use and sent the correct part. Thanks so much for making this process easy.
Parts Used:
Turntable Roller Guide
  • Cynthia from Wylie, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out light in microwave
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.
Parts Used:
Light Bulb - 40W
  • DANNY from SAINT JOHNS, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out bulb
Husband replaced the bulb
Parts Used:
Light Bulb - 40W
  • Theresa from OVERLAND PARK, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not start
Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos
Parts Used:
Door Interlock Switch Kit
  • LENNARD from BURNSVILLE, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stem broken off the turntable base so the turntable wouldn't rotate
Removed the broken plastic base that the glass turntable sets on and put in the new plastic base. Took 5 seconds max! The part arrived in about 24 hours! Great service!
Parts Used:
Turntable Roller Guide
  • Joellyn from Olathe, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic latch to lock the microwave door broke.
Did an online search for repairs and found PartSelect. Simple to order the part and had it installed myself less than a week later. Thank you!!
Parts Used:
Door Latch
  • Richard from Arlington, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
origianl door had a hole in it
replaced door frame assy
Parts Used:
FRAME-DOOR
  • Norman from Rehoboth Beach, DE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The cover to my lamps both broke.
Had to put one screw in each. A little hard to reach up. also hard at first to get them in.
Parts Used:
Light Cover - Clear
  • Peggy from Hastings, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable roller shaft was broken.
Put in the new part, took less than a minute...
Parts Used:
Turntable Roller Guide
  • Juan from Los Angeles, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Parts Used:
Light Bulb - 40W
  • Jerry from Pine, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lightbulb burned out
Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business
Parts Used:
Light Bulb - 40W
  • Roland R from NORTH ANDOVER, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Exterior light bulb (PS2376034) broken off in socket. No access for pliers after glass cover removed.
Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.
Parts Used:
Light Bulb - 40W
  • Alvin from HILTON HEAD, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No problem
I had a son put in the new light bulbs. Rather simple
Parts Used:
Light Bulb - 120V 25W
  • Janet from PITTSFORD, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light over range burned out
Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.

Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/delivery was fast. No need to have spare on hand.
Parts Used:
Light Bulb - 120V 25W
  • Vincent from CHICAGO, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JMV8196AAB
31 - 45 of 77
Back to Top