JJW9630AAB Jenn-Air Wall Oven - Instructions

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

Watched the video and it was as easy as described. Not many things go as easily as this.

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

Followed video

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

Followed provided video

I watched the youtube video that was provided by this website on my computer while doing this repair step by step. It was a snap!

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

I watched your video and read how easy the repair was to do from other buyers. I called sears and they wanted $125.00 just for the service call and automatic 1 hour labor and did not include parts and a 8 day wait for the service call.I called your number and explained my problem and was told what to order. The element was ordered on Easter Sunday and arrived on Tuesday. It took 5 minutes to install. Thank you

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou