Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JJW8527DDQ > Instructions

JJW8527DDQ Jenn-Air Wall Oven - Instructions

All installation instructions for JJW8527DDQ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JJW8527DDQ
1-15 of 29
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burned terminal block and filter board

  • Customer: Joseph from Decatur, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 75 of 158 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

Door would not close tight - light would stay on.

  • Customer: MICHELLE from IMPERIAL, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench (Adjustable)
  • 16 of 27 people found this instruction helpful
Replaced the hinges, the appliance never really shut 100% and after several year it got worse. Now it is perfect and we don't have any problem with heat up time of oven, used to take extra long to get to desired temp. Should have sent it back in the beginning.

oven temp wrong

  • Customer: Alan from Wallkill, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

Door hinges needed replaced

  • Customer: Teresa from Tomball, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 14 people found this instruction helpful
This was an easy repair and the parts fit perfectly. I removed the oven door by unlatching it and sliding it off. I then used a screwdriver to take the back cover off, and took the old hinges off with the screwdriver and replaced them with the two new ones that I ordered. I replaced the back of the door panel and put the screws back in and WA LA - just slid the door back on and tightened the latches.

oven wouldn't heat and showed a error message of function not available

  • Customer: Eugene from Pampa, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

oven had error messages

  • Customer: dan from Gallatin, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 3 of 4 people found this instruction helpful
I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

I needed a broiler pan

  • Customer: Rhoda P. from Secaucus, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 9 people found this instruction helpful
I took the broiler pan out of the shipping container and put it in the oven.

Oven stopped heating

  • Customer: Christopher from Royal Oak, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 3 of 6 people found this instruction helpful
I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

Oven door would not close all the way, light stays on.

  • Customer: John from Newport, RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
First I removed the oven door - with door fully open pull the clips on the hinges all the way out, then close door as far as it will go and lift the door up and off the oven.

Then I removed the three screws on each side, that hold the oven to the wooden cabinet. I then slid the oven unit out from the cabinet about 6 inches, to gain access to the hinge receptacles.

I then removed the 2 screws that secure the receptables to the oven body, and replaced the receptacles.

Reverse steps to put it back together.

Works like a charm.

Had a fault that tripped oven off code was DB92

  • Customer: Bryan from FRANKLIN, VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench (Adjustable)
  • 1 of 1 people found this instruction helpful
Removed both oven doors to remove from the wall. Pulled the oven out of the wall. Removed all the sheet metal backing on the back of oven top and bottom. Removed the electrical,connections to the fan. Removed attach,net screws and pulled the fan. A bit of a pain had to twist pull and bend the metal bracket. Replacement fan had to be reversed came apart easily and reversed then reassembled. Fit in easily and attached electrical connections. Then reattached all the sheet metal backing bottom then top. Put oven back in wall then secured in place. Re installed the doors and applied power. Oven worked great as soon as we tested it. Great fix, works better than new!

Oven door would not fully close

  • Customer: Cameron from MECHANICSVLLE, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Rotated the hinge lock with a screwdriver, pulled door off hinge bracket, later door on table, removed screws to detach inner door frame from outer door. Three screws to remove each hinge. Very easy.

Needed replacement oven rack.

  • Customer: Bobby K. from Huntsville, TX
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Part was perfect fit. Good product, good value, great service.

Oven door would not close completely

  • Customer: Terence from ATKINSON, NH
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
After watching a you tube video or two, I easily detached the oven door. One of the hinges was jammed, and upon releasing it with a screwdriver, it snapped open and gashed my thumb. This as entirely my fault, I did not realize how much force was held in the spring.... You must remove the bottom frame piece and inside door pan to get to the hinges. All Phillips head screws, and all the same size. Once these are removed the hinges are easily removed with 3 Phillips head screws. While l was this far into it I removed the two layers of glass to clean them on both sides. This requires a small nut driver to remove the channels holding the glass. There are three layers of glass to clean on both sides, quite dirty and brown. Reassembled the whole thing. The door assembly popped right back in, and now functions like new. You can actually see into the oven, without opening the door!

Door hinge no longer hinged

  • Customer: Jerry from COLFAX, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Door fell off so removal of door was easy. Removed screws holding the door together to expose hinges. Removed old hinges that were 3 screws for each hinge. Placed new hinges and installed screws then put door halves back together installed screws and then finally replaced door onto the stove. Mission accomplished

Door would not close tight enough.

  • Customer: Daniel from Rochester Hills, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the door and the screws that secured the oven to the cabinet. Pulled the oven out about four inches to provide access to the hinge brackets. Removed two screws on each bracket and removed the brackets. Reversed the process and all was well. Works like new.
All Instructions for the JJW8527DDQ
1-15 of 29