JJW8527BAW Jenn-Air Wall Oven - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Turned off power at beaker box. Opened oven door. Removed four screws from botton of display panel. Lifted display panel up and out to remove. Unplugged three wire bundles from back of circuit board. Removed four screws holding circuit board and replaced circuit board. Reassembled panel. Turned power back on. Presto.....saved $200.00 from repair estimate.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

carefully. there are many connectors to the board, and while they are pretty much color coded, and I had the wiring schematic, I had to put the new board next to the old, and remove and install each connector one by one. If I had removed all connectors and installed the new board, I would never have been able to reinstall the connections correctly.

Same as the others to get to the bad clock. My old part was a circuit board which was made with white material and manufactured by RoberShaw. The new one was on a green material and by another manufacture. The new one felt a little heavier and look like there were more componets on it. However the plug-in connections and the mounting method was exactly the same. Before reassembly, I used a long handled brush to clean out most of the baking gunk that
had accumulated in this area and I used a clean wipeing cloth to clean the inside glass for the display. The best thing about this was the part came on the Thursday before
Hollowee, I installed it as soon as I got home from work. My wife started baking cookies and cup cakes for trick or
treat and all is well.

I removed the four screws holding the control panel to the oven. I then lifted off the panel and rested it on the the oven rack which I set in the top position and pulled out about a foot. Next, I removed the three plug in cables and removed the two screws from the frame that was holding the clock assembly in place. I put in the new part and reversed the procedure. Total time to replace part was six minutes.

First I removed the two retaining screws that hold the element in place. I then pulled the element out about 3 inches to disconnected the two wire leads. Removed element.

Note: Retain the two screws, the new element doesn't come with new screws.

To install new element simply reverse what you did to remove old element.

1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel.
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!

Replacing the electronic Clock Assembly was a piece of cake - just as earlier DIYers had experienced.

The door hinges were not any harder to replace, but it does not affect the behavior of the door. The light stays on unless we keep the door closed with a hook and anchor ( bent piece of metal and a wooden wedge). Not pretty, but effective. Obviously a design flaw... keeping door closed in this way forces all airflow to top and has melted the paint into a wrinkled surface. We had a service person replace the gasket seal and hinges before, but the problem still persists. I did discover that soaking the light cover in a cola drink overnight did a splendid job of cleaning off the gunk.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

My son removed the switch panel and unpluged
the switch. Then he replaced it with the new
switch fasten back the panel and turned the
power back on and everythiing worked fine.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.