JJTU8100XTP1 Whirlpool Trash Compactor - Instructions

This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.

Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.

Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.

The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less than 30 minutes including cleanup.The wife happy,that all that matters.
Jack

As per directions

I pulled the unit out and tipped it over . I pulled the pan off the bottom then i could put a box end wrench on the screw that was jamed then tuned the screw to loosen the door . i then removed the plastic bag that was wrapped around the screw and put the new nut on and all fixed

Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.

REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES

Removed and replaced in less than 15 minutes. Works like new again

took appliance out of cabinet, found the problem to be two nuts on the big screw bars that drive the compaction machine up and down. These things were wore out. We replaced them and turn the electricity back on and tried the compactor and it worked perfect. Of course here was to top cover that had to be removed and reinstalled . all in all it wasn't to difficult. A new machine cost 1100 dollars. This old one bought in 1988 cost 350 dollars. so thank God this fixed it.

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Only needed a flat blade screwdriver and a socket set to remove the top and the "cages" that held the power nuts. Failed to properly restrain the ram but didn't effect the repair. Installed the new power nuts outside of the unit then placed the ram assembly on the worm screws and all was well. Applied grease to the worm screws after assembly.

layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake