JGP336WEV4WW General Electric Cooktop - Instructions

Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.

Removed six screws on the back panel. Just switched six wires from the old to the new module. Stove burners work perfectly now.

The replacement part not right size for the porcelain cone for gas. Had to unscrew 2 screws remove the cone, after unclicking gas wire. The gas spreader did not fit with the cone in place.

Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.

I replaced the igniter under the knob.

Removed several screws and removed element. Replaced same. Total ten minutes.

I received a defective part from PartsSelect.com. After contacting their Customer Service, they promptly replaced the part for no charge at all. I am very, very pleased with PartsSelect.com and recommend them to all "home mechanics".

The bowl was replaced by removing two screws, removing the igniter wire, clip, and igniter. Reverse to re-assemble. I would recommend replacing the gasket at the same time.

Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.

The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again

Real simple to do. Simply remove the two screws holding the bowl and disconnect the electric wire. Obviously first pull the power cord to prevent being shocked.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.

It was so easy.I removed the old part with the new with pliers. Voila/// it worked.

Easy, just remove two top screws, unplug the igniter wire and then do it in reverse. Your're done in less than 15min.

Ok - I LOVE THIS COMPANY!! When I read the other blogs I was a little confused. Ok first choosing the right drip pan for my gas stovetop was a little confusing because there was a cheaper one that look just like mine. I didn't have the model number - so I WOULD have guessed on it. Later I took my stovetop apart and found model number. Found that MY model required the more expensive drip pans. I think this will help people.... (1) Both type of drip pans looked just alike, but the space between the ignitor and the flame was different. The closer one wouldn't have worked. (2) They were categorized as small medium and large drip pans. BUT - they all had the same dimension: 9 inches. The difference is made in the flame area. My stove top has one small flame area, one large and two mediums, that's how you determine which size you need. (3) The ignitor, when you take it off - nothing shows whether the little white ignitor breaks apart or not, and HOW you get it out. Once you remove the little wire holding it to the drippan, don't try to pull apart the white ignitor, it doesn't come apart. Mine had rusty residue attaached, making it hard to pull through. But when I removed the crusty stuff the white thing popped through the hole. (I called a REP to see if the white thing tore apart or not and they weren't sure. So maybe this will help some other woman who is wondering.) This was ABSOLUTELY the easiest and most cost effective way to have a nearly BRAND NEW stove top. And I'm pleased with myself that I did it without any help.

Removed two small screws, removed old bowl, placed new bowl, replaced screws.

Removed two screws holding drip bowl in place. Removed spring clip holding igniter to drip bowl and removed igniter. Installed igniter to new drip bowl and installed drip bowl to cook top. Took less than 5 minutes.