JES9800AAW Jenn-Air Range - Instructions

we removed the back I had my dad help me so he removed the wires while I removed the screws on the inside. When I received the part he also helped me replace it by putting on the wires while I put the screws in. Remember to disconnect from electricity.

First I fliped the curcuit breaker to eleminate power to the stove. Then removed the 2 screws that hold the element in place. Then carefully pull the element out and disconnect. Installed new element to connectors and gently pushed back into the stove housing. Secured with the removed screws and turned back on the curcuit breaker. Turned on the oven and it worked like a charm..

I ordered the part and it came in within 2 days from fedex! Great timing. It took me all of 10 minutes to fix the coil at the bottom of the oven. Fixed the problem and had plenty of time to cook dinner before my husband came home!!
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.

Thank you

Couldn't hook up the wires since the instructions were so cryptic. Ended up fixing old control and re-installed it. Worked fine.

removed the old by pulling it out of track and replaced it with the new filter

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

Took out two screws in the back of the oven that held in the bake element. Pulled the element out of the back of the oven to expose the wires. Pulled the wires off the broken element and then reattached the wires to the new element, put it back into place. Reattached the screws. Done in less than five minutes.

Actually a very simple repair. Determined that the problem was a burned out bake element since broiler worked fine. Looked up part on-line...diagram on PartsSelect made this very easy.
Ordered part selecting normal shipping (part arrived in 3 days). Repair: 1) turned power off at the breaker box 2) removed baking shelves. 3) removed the two mounting screws holding old bake element in place 4) gently pulled the bake element out of the oven until about two inches of electrical wire were exposed. 5) removed the electrical clips from the old bake element. This required steady wiggle to get them off. 6) attached the electrical clips to appropriate ends of new element ensuring they are well seated 7) pushed electrical wires back into the oven and mounted the element using same two screws. Turning the power back on at the breaker, I then tested the repair. No problems noted...turned oven off and replaced the baking shelves. Baked homed made bread that evening.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Your site really helped out alot. Job was farily easy and now we have heat. Difficult part was reaching the wires in the back. Thanks again! TZak

My husband did it was really easy ,he turned the power off to the stove,took the back cover off the stove with a screwdriver and pulled the old one out,then he slipped the new one in connected the wires ,it took less than 15 minutes that simple.

Simple process. Pull the unit out approximately 6 inches. Remove 2 phillips head screws on the left side panel which is about 3 inches wide and runs from the top to the bottom of the unit. No need to remove the panel on the right. Two hex head screws hold each hinge in and are visible once the oven door is removed by opening the door about 20 degrees and lifting it off the hinges. Once the door is off, simply remove the two hex head/self tapping screws holding each hinge in place and remove the hinges from the rear of the front of the oven. Reverse the process to install the new hinges. Do not over tighten but remember they are self tapping and need just a bit of tightening until the hings feels solid. Replace the door by sliding it over the hinges and you're done.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

The process would have been easy except the wiring to the element had a problem. One wire was too short which meant pulling the entire stove assembly out to reroute the wire.The part worked fine; the problem was with initial wiring of stove.