Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JES9800AAB > Instructions

JES9800AAB Jenn-Air Range - Instructions

All installation instructions for JES9800AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAB
226-240 of 390
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not turn on

  • Customer: Stacey from Tampa, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

Burner stays hot

  • Customer: Gregory from snellville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.

very old grease filter.

  • Customer: Eliane from Potomac Falls, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.

uneven cooking temperature during cooking

  • Customer: CINDY from EMMETT, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
had to recalibrate temp control degrees

Element burnt

  • Customer: Marcia from Davis, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took off front door (2)took off two scews holding the element....(3)pulled the element out a couple of inchs....(4)pulled clips off element on both sides....(5)then reversed procedure with new element....Easy as pie.

Simply replace the grease filter

  • Customer: MaryAnn from Scituate, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Thanks for carrying this part for my old stove. And thanks for the great service.

worn gasket

  • Customer: Donald from Newport News, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old gasket and replaced with new gasket'

The bake element was out.

  • Customer: Mary from Montgomery City, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First we watched a video on how to repair it. Then just followed through with the instructions. The part was delivered to my house in just a couple days.

Had defective bake element

  • Customer: Robert from Seguin, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced element. Wires to short to replace element from front. Removed back panel and acessed connections to new element. Was easy even tho had to remove back panel because of short wires.

Burner would stay on high, on all settings.

  • Customer: Robert from Attleboro, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob

temperature varied in oven.couldn't set

  • Customer: tom from winter haven, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

Element arching, not heating

  • Customer: Steven from Ira Twp, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched online video and performed same steps. Video excellent.

element for bottom of ove burnrd out

  • Customer: Anna S from Murphy, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
husband un hooked thr old element and reinstalled the new one. works great - no problems

Top oven sensor

  • Customer: Alan from Bonita, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Burner always on high, no temp. adjustment.

  • Customer: Woody from New Castle, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!
All Instructions for the JES9800AAB
226-240 of 390