Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JES8850BAS > Instructions

JES8850BAS Jenn-Air Range - Instructions

All installation instructions for JES8850BAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES8850BAS
61-75 of 156
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven temperature fluctuates

  • Customer: Larry from SOLON, IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Oven would not hold temperature, not turn on, and would shut off during use.

  • Customer: John from Arvada, CO
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

oven convection fan motor did not work

  • Customer: Sandra from Schwenksville, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
My husband replaced the convection fan with the one we ordered from your service. It was easy for him to repair and took approximately 1/2 hour. We were very happy with how quickly we received the part from your company. He had my oven fixed in time for me to do all of my holiday baking.

oven not heating to set temp. 100 degrees too cold

  • Customer: Robert from Funston, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Broken Inner Glass Pane

  • Customer: Joseph from Lewiston, ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

oven door seal

  • Customer: David from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
easily pulled old seal out and push new seal in place simple and quick.

I'd damaged the old door seal

  • Customer: kerry from oldsmar, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

F1-1 and F3-1 error code

  • Customer: Barbara from Lakeville, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Oven not heating to desired temp

  • Customer: Raymond from Ridgecrest, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Oven Over Heating

  • Customer: Steve from New Albany, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Oven would not heat

  • Customer: Ralph from Nicholasville, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot

  • Customer: Philip from Winter Haven, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Getting codes and beeping

  • Customer: Arthur from Dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 4 people found this instruction helpful
Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

Top oven element works, but bottom element works only intermittently

  • Customer: Bruce from Glencoe, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Oven temperature lagging set temperature by almost 100F

  • Customer: William from Edgewood, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.
All Instructions for the JES8850BAS
61-75 of 156