Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JES8850BAF

JES8850BAF Jenn-Air Range - Overview

Get Parts and Repair Help for JES8850BAF

If you know the range repair part you need, you can browse the list of all parts on the JES8850BAF, or you can search by name or part description. You can also find your part by where it is located on the JES8850BAF by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JES8850BAF parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the int...

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$19.02

Burner Knob

Sold individually. This knob accepts a D-shaped shaft.

$44.96

Door Gasket

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Before making any repairs to your oven you should make sure to wear work gloves to protect your hands, and give your oven time to cool. The only tool you will need to make this repair is a pair of needle nose pliers. This oven door gasket comes with built in retaining clips; if any retaining clips from your old gasket are left in the oven make sure to remove them before installing your new gasket.

$53.63

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware ...

$18.11

Control Knob

Sold individually. This knob accepts a D-shaped shaft.

$66.33

Inner Door Glass Pane

Glass only.

$18.11

KNOB FLEX

Sold individually. This knob accepts a D-shaped shaft.

$19.52

Terminal Block

This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to th...

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 122 of 141 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

F1-1 code

  • Customer: charles from marstons mills, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 55 of 70 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more

Needed to replace oven door gasket.

  • Customer: Lori from Scottsdale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 50 of 61 people found this instruction helpful
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum. read more