JDS9860CDS00 Jenn-Air Range - Instructions

Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.

Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

Just placed it at the filter location. Liked the ring feature on the filter for ease of removal for cleaning. My previous ones didn't have such feature. Thank you for filling my order. I bought an extra filter for the future. I'm a big user of my Jenn-Air range. I may soon be needing to replace my griddle. Will be contacting your company then.

First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.

This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.

I simply lifted off the grille in the center of the stove, pulled out the old filter and dropped the new one in. It sits at an angle (right side down, left side up) rather than slotting in to a particular spot.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

removed oven door, removed screws from bottom and sided, door is in layers, removed door layers like taking apart a sanwhich layer by layer, once i got to the inner layer i just had to bend out the little tab on the frame,remove the broken pane and place in the new one, bend the tab back and then put the door back together layer by layer, it was very easy and saved me money, and frustration in dealing with a repair man from a well known company who tried to tell me I needed to replace the whole door as the glass was factory sealed in the door, WELL! this girl's hair may be blonde but not that blonde, I received the glass the very next day, and it took me 40 minutes tops to replace the glass, EASY! KC

unscrewed and unplugged the old one and plugged in and screwed in the new one. EASY!

Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.