JDE1000A Jenn-Air Dryer - Instructions

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

Took the front of dryer apart removed belt and drum replaced my parts and reassembled.

removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover

popped front off took blower front off took fan off put new one on replaced cover & front. job done. ordered fan on thursday got it on friday great service.

I just used screw driver to pop of clip put new roller on poped clip back on

I popped the top off and tipped the dry over . It took 2 to reposition the drum and belt back after taking it out and remving the old wheel and replacing it.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

When online& found website... trouble shot for problem per previous posts on PART SELECT.GREAT SITE for problem ifo.I ordered parts,they arrived 2 days later and within 1/2 an hour I had our dryer repaired and working like new!!THANKS!!!

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.

I followed the "How to" video on your web site. Most importantly, I cleaned the entire filter area which probably caused the problem as your instructions recommended. I will do that annually going forward. I would recommend your service to anyone.

Replaced the thermal shut off and the thermistor located on the heating element bracket.
Easy to diagnose and to replace- not totally accessable but not that bad either. Cleaned out lint obstruction causing the problem.

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

Unplug - use screwdriver to release top latches.
Raise top to more than 90 degrees - hard on hands or head if it falls. Remove wires from door swithch and remove front panel screws, lift off front cover. Remove screws from front paned of blower housing. Remove snap ring - shaft clamp already loose, remove old blower whee and install new one. Use DEEP(spark plug) socket tap new wheel onto shaft, replace clamp and snapring and reinstall panel on housing, put front panel back-install door switch wires before screws, replace top, plug in and test run.(note 1st word correction)