JDB6510AWP Jenn-Air Dishwasher - Instructions

Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

First I turned off the circuit breaker to dishwasher. Then removed the lower spinner and related parts. The water in the bottom needs to be sucked out with a shop vac next, because when the pump screws are removed any remaining water will drain underneath onto the floor. Remove the wash pump and drain rotor.
Remove the front bottom plate to access underneath, unplug the electric motor and thermister. Unscrew both hoses,drain and upper wash arm. Move the locking ring to release the the entire assembly up into the dishwasher.
The kit I bought had most of all the washer parts included, so on reassembly I used the new ones. The rest when back together in reverse order after a good cleaning. Since the thing was apart anyway why not clean up all the filters on reassembly. The kit also came with complete instructions.

Replacing my dishwasher racks was very easy. I followed the guidance on the PartsSelect.com website for replacing the upper rack. Replacing the lower rack was only challenging when I couldn't figure out how to remove the water sprayer from the old rack and place it in the new rack. A quick search on Google.com and I learned to turn the sprayer counter-clockwise to remove it and then clockwise to put it in the new rack. Worked like a charm! I would recommend PartsSelect.com to anyone. Easy to use, parts came quickly, and I appreciated the guidance from others.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

We had had a slow leak on our dishwasher for some time. We were also getting a film left on the dishes and they did not appear clean. Eventually the leak got worse and I had to find the problem. It turned out that in addition to the motor shaft seal leaking, the heating element was out and the installer had done a really bad job, with leaks in the fittings and the wiring not installed properly.

I tried to get the parts locally but they were not in stock and needed a week to arrive. With family coming to visit, I ordered the parts from Parts Select on Monday and they arrived Tuesday. That afternoon, I had everything back together and it is working great.

I aligned the V-shaped tabs on the inner side of the part with the slots in the mating part and simply pulled the old part out (it was already disengaged from the wheels in the metal rail). I then inserted the new part into the slots. One side went in well, but the other side required the part to be bowed slightly to match up the V-shaped tab with the slot. Then the hard part was getting the wheels in position to snap them on. Once in position, it took a bit of effort to engage the snaps in each wheel. I was afraid of breaking the new part. These snaps are very stiff and even with the notch between them there isn't any give, but I was able to apply enough constant, steady pressure to finally get them to snap in without breaking.

Kids blame mom, mom blames cleaning lady. I blame cheap plastic part. ez install. Make your job ez wait for a helper to come home. When you undue 10 screws, second person can hold inner panel and door apart.

Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!

I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.

Repair was simple. Diagnosis was wrong. Switch did not fix problem. Most likely a control electronic assembly.

removed the agitator,and a couple of baskets til i was able to gain access to the pump impeller & pump housing. i replace those parts,put back together,all works great now

1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.

took old handle off (loosened two screws to do this) and replaced same way.......took two people only because one held the door separated while the other replaced the handle........