Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JCD2389GES > Instructions

JCD2389GES Jenn-Air Refrigerator - Instructions

All installation instructions for JCD2389GES parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JCD2389GES
616-630 of 942
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker tray in side by side leaked and created large lumps of ice

  • Customer: Catherine from Punta Gorda, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Stopped making ice, leaking water into freezer to kitchen floor!

  • Customer: John from Seabrook, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

My refrigerator light did not work.

  • Customer: Fred from Warwick, RI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

I broke the plastic cover for the egg tray in my refrigerator door

  • Customer: Pauline from Milliken, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the part. It came and I popped it in. What made me so happy is the ease of finding the part I needed on your website as well as its speedy delivery! Thank you!!

ice maker inopeative

  • Customer: George from Minden, NV
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
went on line and ordered new ice maker for this model refrigerator. Received the new part. New icemaker provided video for replacement of ice maker.Used the video showing the removal and replacement of the ice maker to begin the removal process. (must remove one mounting screw, then raise the icemaker up then out to unlatch the fixture.) This took over one hour, then had to remove wiring arness. Instrucions indicated to "squeez" the locking clip holding the connector, it is impossible to see the connector so it was a "feel" process. It turned out that squeesing the connector from the sides, did not work, finally squeezing the locking clip (top to bottom) finally released the connector. Then the installation (per video) reversed the removal procedure and that turned out to be about a two hour task because to align the ice maker when you cannot see the alignment / holding brackets was a very difficullt task. Then when it was finally installed, the one mounting screw, would not align with the previous mounting hole, because the tab on the new one was longer, requiring drilling a new hole to hold the icemaker in place. The hole had to be made using the same (self-tapping) screw, since the space available when the icemaker is installed is very limited. After the mounting hole was partally made, driving the screw the rest of the way had to be done with a ratchet, other then that, everything was just great.

The ice maker stopped working and left "kling-ons" in the tray. At one time the trays kept trying to fill which only sent water pouring into the freezer compartment.

  • Customer: Patrick from Fairfax, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Searching Google and Youtube produced trouble-shooting guidance to first check the water inlet valve which I did. I should have realized the valve was working since the ice-maker was trying to fill the trays. Additional advice recommended skipping all the other component troubleshooting and merely replace the old unit which I did. The big difference with the Amana appliance was the icemaker was installed laterally in the back of the freezer rather than longitudinally with the end of the control wheel positioned towards the front of the freezer. This created a tight fit in removing the old unit, especially since the wiring harness was extremely short. The latter made access to the plug release catch difficult. I used a small flat blade screwdriver and worked mainly by feel to release the plug catch. Persistent wrangling finally got the plug detached and the unit free. The water inlet hose also had a rear access orientation while the replacement unit had access was from the side. The hacksaw blade was used to cut a pre-outlined access to allow the hose to enter from the rear as with the old unit. Once the shut-off bail was transferred, wiring harness reconnected, and water inlet positioned and clipped into place, the mounting screws were secured. Within 24 hrs the first ice cubes popped and the unit has filled the ice reservoir. Keep in mind I just ordered the icemaker and did not need any other add-ons like a different wiring harness which seemed to work fine. Confirm when you order you don't need any additional parts. Good service for PartSelect. I will use them again.

Freezer compartment coils would not defrost causing the refrigerator side compartment not to stay cold.

  • Customer: Jerry from Fowler, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off the refrigerator. Removed the freezer storage baskets. Removed two screws on the back panel. Removed the top and bottom panels. Unplugged and unclipped the wires above the coils. Removed the metal tub holding the heater in place on the right side of the coil. Removed the clip from the bottom of the coil holding the heater up and then carefully guided the wire harness from along side of the coils and removed the heater. To install the new heater thermal assembly I just reversed the order that I took the old one out.

The door to the ice dispenser broke off

  • Customer: Cristine from Ofallon, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
When calling to see what the repair would cost my prices ranged from 250.00 to 175.00 with parts and labor. But I decided to tackle this project myself after watching the installation video. My parts arrived quickly and I watched the video had my repair completed within 30min and saved myself over 100.00 dollars. Thank you PartSelect!! The step by step instructions made this project a breeze.

Ice maker started spilling water and then stopped making ice

  • Customer: Daniel from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1. Watch the video. 2. Save your old ice maker's cover, metal lift bar, and power cord and clip. New one does not come with the cover, metal lift bar and power cord and power cord clip 3. My ice maker had three screw. two on top that only need to be loosened. on e on the bottom that has to be removed

Refrigerator stopped cooling compressor did not cycle

  • Customer: james from indian springs, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug power! Remove the screws from lower panel on back of refrigerator. Lift wire mount out of back panel. Capacitor is mounted directly to the relay and overload switch located on the left side of the compressor. Remove the spring clip holding the capacitor in place and pull the old capacitor out. Plug in new capacitor and replace spring clip. Use vacuum to remove dust from drip pan and wipe fan blades clean. Replace wire into slot on back panel and replace screws. Remove front coil cover below freezer door. vacuum dust off coils and replace cover. Plug refrigerator in and enjoy cold beverages. Relay and overload kit were not required for this repair.

Fridge side to warm - freezer ice up

  • Customer: Ralph from Athens, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
followed directions from parts direct video worked like a charm very easy

Ice maker was leaking and needed to be replaced

  • Customer: Rochelle from New City, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions shown on the YouTube video on the Parts Select site. I had to make a few modifications. There were two nuts that had to be loosened to lift the ice maker off the freezer wall. The mounting bracket had to be transferred from the old icemaker to the new one to align with the hole in the freezer to reattach. The white wire went under the clip was a black wire but it was easily recognized. Other than that it was very straight forward and I had new ice in a few hours. I would definitely do it again.

Plastic tip broke off the insulated flap. Would not seal against icemaker.

  • Customer: William from Heath, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed two screws from face plate then nudged plate up until it cleared the two top screws. Removed three screws holding the actual kit in place. Gently pulled the unit forward and pulled the water tube out from above the kit, then disconnected the wires connecting the unit. At this time the unit is separated from the refrigerator and you can disconnect the solenoid to remove it. The plunger in the solenoid was a little different from the old one as it connects to the insulator flap bar but Partselect has made a good/easy modification for replacement. Before installation I recommend lubricating the plastic actuator switch. Reverse the procedures you used to access the unit. Very easy.

Original ice maker failed to make ice

  • Customer: Steve from Kerrville, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the ice maker. I have a 3 door refrig. It has a bottom drawer freezer. Remove the freezer door to make this much simpler. On my unit, the ice maker is installed with three screws, rather than one and two clips. Check before you try to pull it out. You should unplug the old ice maker from the refrig, leaving the wires on the old ice maker. It's much easier to remove the old wiring harness from the old ice maker once you've removed the front plastic cover on the unit. Both plugs on the harness have clips on them to prevent accidental disconnections. Be sure to find and press the clip releases before you pull on the wires. Nut driver makes this job easier than screw driver. You only need one size for all screws. I used the old ice maker bottom mounting clip rather than trying to bend the new one to shape. Much easier. My old ice maker had an extra wiring clip, which I moved to the new unit before the install. There is one wiring clip to hold the temperature probe, and another just to keep the wires neat. Letting the old ice maker front plastic cover warm up a bit before you try to pry it off for reuse is a good idea. Less chance of cracking. Two hours after the install, I had new ice in the ice bin.

The freezer part of my Maytag Wide by Side was icing up every 2- 4 weeks, whereby I had to defrost it. This went on for 5 years.. My wife wanted me to junk it, but I paid big bucks for it in the beginning and I wanted to try out the PartSelect part first.

  • Customer: Robert from Liberty, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video instructions by the friendly repairman from PartsSelect.. I did it, but I needed just a bit more patience as he said, and I thus broke off one of the plastic tabs in the housing (I hate plastic fasteners!!!). But some redundancy was obviously built in, so it still was OK. This is day 37 since I repaired it, and the freezer has not iced up yet! And this is in 95 degree prolonged weather outside! You've helped to make our lives a lot easier! Thanks, you've earned my respect and my future repeat business.
All Instructions for the JCD2389GES
616-630 of 942