Parts That Fix Hotpoint Dryer HTDX100ED6WW Marks left on clothes
Marks left on clothes is a commonly reported symptom for the HTDX100ED6WW Hotpoint Dryer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your HTDX100ED6WW Hotpoint Dryer that will fix Marks left on clothes. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.
Replacing your General Electric Dryer Duct Felt Seal
Customer Repair Stories
Dryer leaving stains on clothes
-
Tahir from ARLINGTON, MA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
the felt in front door worn out
-
gerard from goldsboro, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
The lint chute assembly houses the lint filter and channels exhaust air from the drum to the blower wheel.
Replacing your General Electric Dryer Dryer Lint Chute Assembly
Customer Repair Stories
a lot
-
Craig from HOPKINS, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Catching clothing and reping
-
Jose from LILBURN, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
If your dryer is excessively noisy when operating, is not tumbling, or is leaving marks on your laundry, it may be time to replace the drum glides. The drum glide bearing is a genuine OEM part for your dryer and is used to help the drum rotate smoothly and quietly. If the bearing has worn out, it can make your dryer noisy when operating, with a metal-on-metal sound. Please be sure to disconnect the power supply to the dryer before beginning this repair.
Customer Repair Stories
Dryer was making noise
-
Maurice from MINERAL SPGS, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums will scrape against metal during the drying cycle which will produce a squealing, or scraping sound.
Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.
Replacing your General Electric Dryer TOP BEARING
Also known as Drum Mounting Hub.
Customer Repair Stories
Heat deflector was covered in melted plastic
-
Charles from Alexandria, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Deflector was covered in burnt something.
Had I had the proper tools the repair would probably have taken 30 minutes or less.
-
Richard from San Antonio, FL
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Wrench set
This is a lint filter screen that is used for many dryers. It has a metal screen with a white plastic frame, and is approximately 13 inches wide. This part is sold individually. The lint filter traps lint while clothes are being dried and prevents the lint from building up in clothes and internal parts of your appliance. Neglecting to clean your filter on a regular basis can negatively affect the operation of your dryer and is also a fire hazard. Be sure to clean your filter on a regular basis. Installation is easy, simply slide the filter in and out of the filter slot.
Customer Repair Stories
new lint filter
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......
-
william from simi valley, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
replacement of holed lint screen
-
Mark from Clarksville, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins