HGI8054UC (04) Bosch Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Igniter replacement
Getting to the igniter is trivial, only requiring the removal of the stove bottom (two set screws) and a heat shield (the heat shield is held in place by screws with size 20 star-driver heads). At this point a splice could be made to the original wires, IF ceramic wire nuts were included with the replacement igniter (but, alas, they are not). IF a splice were made the repair would be a very easy, 10-minute job.
To replace the igniter then requires the complete removal of the back of the range (17, size 20 star-driver, screws, if I remember correctly), plus the removal of an additional heat shield (one more screw). Then one must carefully lift and free the back from tabs on both sides that are set into slots. (Oh, and you probably want to loosen the electrical cord shield that interferes with the back coming off.) The new igniter wire plug is only then very easily re-attached to existing harness. Everything is then replaced to finish the repair.
None of this is difficult, if you don't mind moving your range away from the wall and dealing with on the order of 20 screws. Personally, I think I would have rather found an igniter with ceramic wire nuts to splice to the original wires (certainly not as elegant as replacing igniter and wires entirely, but far quicker and easier).
To replace the igniter then requires the complete removal of the back of the range (17, size 20 star-driver, screws, if I remember correctly), plus the removal of an additional heat shield (one more screw). Then one must carefully lift and free the back from tabs on both sides that are set into slots. (Oh, and you probably want to loosen the electrical cord shield that interferes with the back coming off.) The new igniter wire plug is only then very easily re-attached to existing harness. Everything is then replaced to finish the repair.
None of this is difficult, if you don't mind moving your range away from the wall and dealing with on the order of 20 screws. Personally, I think I would have rather found an igniter with ceramic wire nuts to splice to the original wires (certainly not as elegant as replacing igniter and wires entirely, but far quicker and easier).
Parts Used:
-
Jeffrey from Bloomington, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
10 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Standoffs were not provided. The current standoffs needed to be remove and placed on the new board. (Not easy)
One the standoffs were removed they needed to be trimmed to attach to the new board. Took longer to do this than remove and replace board.
Parts Used:
-
Ruben from STAR, ID
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Control panel would randomly flicker, fade to black or become non-responsive when subjected to the heat/steam of the open range.
Watch the YouTube video.
Turn off power or unplug the range.
Remove 5 gas control knobs.
Remove four T20 screws on Control panel. one on each end, L and R, two underneath, L and R.
Pull off control panel and carefully flip it up onto the range, being careful not to stretch the wiring harness.
Carefully remove two wiring connectors (pinch and pull method)
Remove four T20 screws securing the Control panel mount then turn it over 180 degrees.
Straighten the mounting tabs until the control panel easily slides off of its mount.
Remove and replace the control panel and sheet.
Reverse the procedure to reinstall.
It took me longer to clean the components and the area that to repair the problem.
Tip: Isopropyl alcohol in a spray bottle and a cloth cuts the grease and grime, if needed, with very little effort and no scratching.
Turn off power or unplug the range.
Remove 5 gas control knobs.
Remove four T20 screws on Control panel. one on each end, L and R, two underneath, L and R.
Pull off control panel and carefully flip it up onto the range, being careful not to stretch the wiring harness.
Carefully remove two wiring connectors (pinch and pull method)
Remove four T20 screws securing the Control panel mount then turn it over 180 degrees.
Straighten the mounting tabs until the control panel easily slides off of its mount.
Remove and replace the control panel and sheet.
Reverse the procedure to reinstall.
It took me longer to clean the components and the area that to repair the problem.
Tip: Isopropyl alcohol in a spray bottle and a cloth cuts the grease and grime, if needed, with very little effort and no scratching.
Parts Used:
-
Alan from COLUMBUS, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven was not heating properly
-
Barry from MONROE, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken glass/door won't stay closed
installed new front glass panel.
installed thin magnetic catches on each side of door
installed thin magnetic catches on each side of door
Parts Used:
-
Michael from DES MOINES, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!