Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This Front Drum Bearing (Top Bearing, Dryer Drum Front Support Bearing, Drum Support Bearing, Dryer Drum Glide Bearing) holds the drum bearing and slides for the drum to turn on. The front drum bearin...
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
This set (Knob and Clip Assembly, Control Knob, Dryer Control Knob) allows you to replace the knob on your timer if it is damaged or missing. The plastic knob can break around its shaft, or the retain...
This is a lint filter screen that is used for many dryers. It has a metal screen with a white plastic frame, and is approximately 13 inches wide. This part is sold individually. The lint filter traps ...
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
This is a genuine OEM replacement timer (60Hz) for your dryer. To complete this repair you will need a #2 Phillips screwdriver. To access the timer, you will need to remove the top of the back panel. ...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
8 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Theresa
November 30, 2019
My dryer won’t keep running once you hit the start button. We replaced the start switch, but the dryer won’t stay on. We use a brick to keep it on currently. It works fine otherwise.
For model number GTDP180ED0WW
Hi Theresa, try replacing the interlock/belt switch PS1481922. Thank you for your question and good luck with your repair!
Hello Florine, thank you for your question. There is a video on how to install that part at the following link.
https://www.partselect.com/PS1766009-GE-WE12M29-Drive-Belt.htm?SourceCode=4&SearchTerm=GTDP180ED0WW&ModelNum=GTDP180ED0WW
I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lynn
April 5, 2022
My dryer does not heat. Had thermostats and element tested, they are showing continuity. Is there a thermal fuse on this dryer and where is it located?
For model number GTDP180ED0WW
Hello Lynn, thank you for writing. We believe for this model the(thermal fuse) is the high limit thermostat is on the side of the housing for the heating element. To test the thermostat PS267900, you will need a Ohm meter to check for resistance. We have a video for you to access. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hello Diana, Thank you for contacting PartSelect.com. Very sorry but we do not have the age of the appliance, just parts lists and diagrams. For more specialized assistance or to speak with someone about this, we would suggest calling the manufacturer of the appliance directly. We hope this helps!
Was this helpful?
Thank you for voting!
Layne
December 7, 2022
We have to run the dryer twice to get the clothes dry, what part do you recommend because I don't want to buy a bunch of parts or a new dryer
For model number GTDP180ED0WW
Hello Layne, thank you for the question. Our research on your model shows that you may need to check if the gasket is intact and in good condition. If it is in good condition, you may need to replace the cycling thermostat, part number PS267926, and the high-limit thermostat, part number PS267900. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and
... Read more drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel sl
... Read moreightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.
Basically, I followed the same steps a prior person posted. 1.Removed the two screws inside the door, on the top part of the opening. 2.Lifted up and removed the top. 3.Removed two screws holding the front panel in place. 4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at
... Read morethe drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them. 5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it. 6.Checked to see how the old felt was installed, then I pulled out the old felt. 7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed. 8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock. 9.Removed a surplus plastic piece from the new drum bearing (where the light comes through). 10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight. 11.Lifted up the drum and put the front panel back on. 12.Screwed the front panel back on, using the two screws. 13.Carefully put the top back on. 14.Screwed in the two screws inside the front door to fasten down the top. That was it! I started up the dryer and it worked fine. No more squeaking. About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package. At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
