Models > GLMV168CQ1 > Instructions

GLMV168CQ1 Frigidaire Microwave - Instructions

All Instructions for the GLMV168CQ1
1 - 5 of 5
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave door window seal damaged.
The "seal" is a clear plastic sheet that forms the inner most layer of the "window" in the microwave door. If it becomes damaged or doesn't adhere properly, steam and other cooking by-products get inside the door itself. That's what happened in my case. As a result, I had to disassemble the entire door to clean the inside of the glass and other parts. If that cleaning had not been necessary, I could have replaced the seal without disassemblying the door.

To replace the seal, I followed these steps:
1. Used my thumb nail to raise a corner of the old seal.
2. Peeled off the old seal. This leaves a perforated metal layer exposed.
3. Cleaned the metal layer to remove residual adhesive from the old seal.
4. Once the metal layer was dry, my wife and I worked together to peel off the "backing sheet" from the new seal. (One side of the seal has adhesive on it - like the sticky side of tape. After you peal the backing off, the sticky side is exposed.)
5. After we CAREFULLY aligned the seal, I held it while my wife slowly and carefully pressed it into place.

Problems to watch out for:
The seal is shipped "folded". This causes a crease to form in the plastic seal, which makes it difficult, if not impossible to install it without leaving any raised places. Note that raised areas in the center probably just look bad. But, raised areas around the edge may prevent a proper "seal" and result in steam, etc., getting inside the microwave door. I receved two separate seals and both had a crease. PartSelect reps were very nice, but were not able to correct the problem.
Parts Used:
Door Film Seal
  • Freddie from Roanoke, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the bulb
Unscrew the glass lamp cover and replace the bulb. Very simple. The hardest part was to find the bulb. I looked at my local hardware stores but of course they did not have them. This site was great and easy to order. I looked at 3 other sites before finding this one to be the most simplistic to use.
Parts Used:
Microwave Light Bulb
  • Gary from McDonough, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
14 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned out light bulb
removed glass lens with screw driver and removed old bulb and screwed in new bulb....replaced the lens.
Parts Used:
Microwave Light Bulb
  • jack from Tustin, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Couple broke, turntable would not turn
Removed glass turntable, dropped new coupler in slot. Replaced glass turntable. Poured a cup a coffee, placed it in microwave, pushed the 1 min. button. Waited a minute, removed cup and drank my coffee. Total time 1 minute for coffee, 20 sec to replace coupler.
Parts Used:
Turntable Drive Coupler
  • Robert J from GREENVILLE, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable wouldn't turn.
We unscrewed the bottom cover, unplugged the motor, replaced the coupler which essentially connects the glass plate in the microwave to a motor allowing it to go around...zipped everything back up and it now turns.
Parts Used:
Turntable Drive Coupler
  • Georgiana from Rancho Mirage, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLMV168CQ1
1 - 5 of 5