Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GLEQ2152ES0 > Instructions

GLEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for GLEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLEQ2152ES0
211-225 of 403
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was not drying completly.

  • Customer: Scott from Otsego, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.

Dryer element burned out

  • Customer: Robert from Gatlinburg, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video available on the web site. After watching the video, I knew exactly what to do and how to do it. Really made the job a lot easier than it would have been. Some steps were harder to do than the video made them look but I atribute a lot of that to the fact that they were working in a large work shop and I was working in an area not a lot larger than the dryer. The hardest part of the job had nothing to do with changing the element, it dealt more with getting the vent hose off and on. Who ever designed the connection apparartus on dryers, used to connect that stupid hose to the back of it, must know something I don't. I have never had any luck when it comes to being able to get the hose connected and then getting the dryer back in the hole it came out of, without the hose falling off or getting crimped. PartSelect is a great company to deal with. Ordering was easy due to the highly intuitive web site and I got the part in two days. Saved me a lot of time running around town, burning a bunch of gas trying to find find what I needed. Thanks

Door handle top mounting bracket on dryer door busted

  • Customer: Jon Henry from Seabrook, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy fix. Removed remaining bottom mounting screw and removed old door handle. Positioned new handle on dryer making sure it fit properly in it's slots and installed screws into mounting brackets. Worked perfectly.

dryer belt broke

  • Customer: Veronica from Grand Ledge, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Installed just like the video described and it went quite well. The part arrived in a short amount of time and the belt was exactly what I needed.Thank you I will visit your web site again. A very satisfied customer. :) Veronica G.

A loud squeeling sound

  • Customer: Delbert from Grass Valley, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

Dryer was squeaking loudly.

  • Customer: Tim from Sulphur, LA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video instructions....easy as pie. Glad i bought the belt too....the belt on my dryer was very worn. Changed the bearing with the kit. Very easy to do. The whole job was done in an hour and a half....back together and running without the squeak. Glad i repaired instead of buying a new dryer. Next time i have a problem with an appliance, i will be checking PartSelect first.

Squeaking and no heat

  • Customer: Daniel from Jackson, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The main drum bearing was bad and vibrated the heater coil causing the coil to break, real easy fix, take off top cover of dryer, take off front panels and door assembly, lift up drum and pull forward, replace parts =)

loud metal on metal noise

  • Customer: richard from orchard beach, MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced rear bearing on back of dryer. Repair cost $20.00 an a little time. Much better then buying a new dryer. It was easy to repair the video instructions were great. I would do it again it needed.

No heat to dryer

  • Customer: Renee from Coldwater, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Your tutorial video of how to change out the heating element was so helpful, it gave me the confidence to tackle it on my own. It was so detailed, there was no worries of not knowing what to do. Everything was exactly as the video showed, and was very easy to replace this heating element. My wife was thrilled we saved money on doing it ourselves, and grateful to have the dryer working with 3 kids and a husband who works in concrete! Thank You to the Parts Select team for putting such a helpful site for people to utilize!

Dryer Squeaking

  • Customer: Gilbert from Elizabethtown, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found instructions on "UTube"some of the screws were in a different position but you can see them. While you have the dryer apart it's a great time to clean it and also as long as you've gone this far replace the belt,it's probably time.

I shut the door too hard, and the old latch fell down into the inside of the dryer.

  • Customer: Bret from Tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new latch easily snapped it into place.

Loud screeching noise until the dryer warmed up

  • Customer: Marila from Portland, OR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My order confirmation email had a "how to" video for installing the parts I ordered. I just watched the video, and the installation was ridiculously easy! We've put up with the obnoxious screeching noise for probably about two years, and with about $40 in parts and less than an hour of work time, we have practically a new dryer!!

needed to replace drum bearing

  • Customer: Jon from Jenkins, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

No heat.

  • Customer: Werner from Eagle River, AK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. Skill level one task that anyone can perform.

Dryer would not starr

  • Customer: Barbara from Muncie, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged dryer, Removed top of dryer, Removed electrical connection to thermal limiter, tested thermal limiter with meter and found that it was bad,removed defective limiter, ordered part, waited for part (1day), put new thermal limiter in dryer. reattached connections, put top of dryer back on, plugged in dryer, attempted dryer start up and it worked. Very easy because of the information I got on this site. Thank you
All Instructions for the GLEQ2152ES0
211-225 of 403