GI15NDXTQ3 Whirlpool Ice Maker - Instructions

Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well

I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours

I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact.
I then threaded the new wire through the cutting grid frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.

Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes.
My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw.
After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold.
If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!

Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual.

The most difficult part of this order was identifying the part. The manual and picture for this model icemaker called the part a Ice level Sensor. No such item could be identified at Parts Select or at Kitchen Aid. After looking at item after item on the parts diagram it was determined the new name was a bin Thermostat not to be confused with the Thermistor, Ice control.
Replacement was quick and easy and took 5-10 minutes. Working fine now.

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

Took the two pumps tested them with 12 volt Battery. one pump didn't work. Looked up part nomber on Google and it lead me to this Co.

First I removed the cutter grid assembly by removing two screws. Also disconnect the wire that powers the grid. Once on the bench, simply remove the broken cutter wire. String in the new wire, starting at one end and working back and forth to the other end. Tighten the terminal screw on the first end, and then "strum" the wires, one at a times, pulling the wires taught. Pull the excess wire thru the second terminal, until all wires are taught, with equal tension. Tighten the second terminal screw, and cut off excess wire at both ends. Re-assemble cutter grid into Ice Maker.
Problem solved!

Removed ice scoop and holder. Remove front cover and pump bracket. Replaced pump and replaced covers. Started up and working well.

I replaced the bin ice sensor with the new one from partselect.

remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

I called a repairman to come out and he said it would cost $320 dollars for the repair. So I bought the part and spent $85 dollars and about 25 minutes to repair it myself

Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibility. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.