GI1500PHB5 Whirlpool Ice Maker - Instructions

Double check the actual part number. While the item looks the same, my unit had a 3 prong plug while the replacement had only 2 and did not fit.

un screwed the hex screw holding the thermostat and installed the new thermostat and pluged the new part int its place. I undid the front shield so i could get to the plug.

My top grid was broken. After removing the old wire and loosening the screws on both ends of the old wire, I carefully unrolled the new wire so there were no kinks. Next, I put one end of the wire in a vice to hold it in place. I put a loop in the other end and attached it to the one end of the frame. You can then hold the grid in both hands and put tension on the wire as you make the wraps. When you get to the end, attach it to the grid screw and tighten the screw while maintaining tension. You can then cut the remaining wire and reinstall the grid. I think this was much easier than the directions that came with the wire. Took 5 minutes to install the wire on the grid and 15 to 20 minutes to everything back together and start making ice.

went good

I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got the unit back together.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

The real difficulty is removing the screws. Even with a nut driver the space available makes them difficult to remove. I went to the hardware store and replaced the screws with screwdriver slots for re-installation.

I took out old grid and removed the top broken wire. I attached the end of new wire to the terminal screw and carefully threaded the new wire back and forth without kinks. I was not able to get wire as tight as it was originally, but able to get it tight enough with pliers. I attached the other end to the opposite terminal screw. I had plenty of wire for the job and cut off the excess. I re-installed the grid and had ice the following morning. Feeling good about myself and saved a lot of money.

Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

It was easy to remove the old grid and replace it with a new one.

Insalled fan motor,problem went away. Thanks

Follow the instructions already submitted by others. As mentioned be sure to place towel inside to cover the drain. My 3-wire electrical connector also had some corrosion build-up so I had to remove the bracket holding the connecter cut the 3-wires and install a new connector. Not a big deal, you are just working in a small enclosed area. Pulling the entire unit out and either elevating or tilting back helps with the access. Be sure to check drain connection in the back of the unit when putting back in place. Having a headband light helps for entire repair.

Once I determined easier access to the fan motor, I removed the three fan motor screws that held the motor on place. After removing the motor I remove the fan blade assembly held by one nut and reattached to the new motor. I then reattached the new motor with 3 new screws which were provide and reattached the power cord with the cord clip and began reassembling the icemaker housing, then moved the unit back in place which was installed under counter. I could do this repair in less than 45 minutes now that I have done it once. I saved several hundred $ from the original estimate and the parts were delivered in 2 days after I ordered online. This is definitely a DIY project!!

1. Unplug the refrigerator. 2. Remove the back cover at the bottom of the refrigerator. 3. Remove the two screws holding the vertical black bracket the fan is mounted to. This allows the bracket to move easily. The bracket does not have to be removed. 4. Removed the four screws holding the fan bracket to the vertical bracket. 5. Unplug the power connector from the fan motor. 6. Remove the entire fan bracket assembly from the refrigerator. 7. Remove the 4 screws holding the fan motor to the fan motor bracket and unmount the fan motor. 8. Remove the nut holding the fan blade to the fan motor and remove the fan blade. 9. Reverse the process, mounting the fan blade to the new motor, screw the motor to the bracket, screw the bracket to the vertical bracket, screw the vertical bracket to the refrigerator and plug the power connector back into the motor. I did not have to use any of the extra mounting hardware or electrical hardware provided with the kit. It might be a good idea to purchase a new fan blade with the motor kit, the fan blade can get pretty grungy. I cleaned the fan blade with some degreaser before remounting it.