GHW9400PW0 Whirlpool Washer - Instructions

The drum baffle came off. This website provided a diagram to make ordering the part easy. It was reasonbly priced and came in the mail very fast. I had it installed in my washer within 5 minutes. Excellent experience. Thank you.

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Replace old part

Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.

replaced drain pump.Saved 200$

Removed the screws and removed the damaged handle then screwed on the new one

The water inlet vavle was pretty easy to find once I took the top off. The water input hoses connect directly to it and 2 electrical connection per valve. One screw needs to be removed. The only trick is to slide the valve to the left to remove. It is captured by the sheet metal washer housing at the base of the male hose connetion.

The new piece just took seconds to install. You had to set the piece slightly farther back then where it belongs, and with a slight downward pressure, just slide the part toward yourself until you hear it click into place. About 5 seconds and no tools required.

It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)

Cleaned hinge area including the hole where the cover snaps into.Started door window side underneath the clear plastic first and then snaped into place. Door handle replacement used standard set of allen keys and removed broken handle parts. started door handle screws 2ea in new handle mount holes and tightened screws snugley but not tight enough to break the plastic handle.turned out to be a great repair!

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

removed top cover,disconnected wires to valve,removed valve and hooked up a washer hose to test valve,one side was leaking,valve would not close.replaced with new valve that I received in 2 days,do not buy after market.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

part was easy to find , shipping was reasonable easy to install . will buy again thanks .