GHW9150PW0 Whirlpool Washer - Instructions

the repair was so easy. unscrew the old handle and screw in the new. The new handle feels even stronger than the old one felt when we first got the washer.

Slid the washer out, took the hoses off and the back panel then the front panel, found coins in the filter tray and a baby bottle plastic cap was sealinhg the drain going into the plastic filter housing (it fits perfectly) removed all the items and put the white plastic screw cap back on the drain. Next problem was the washer walking around the laundry room, upon fixing the drain problem noticed the front shock absorber was unhooked and two on the right side of the machine had leak some grease, rehook the front shock and ordered two new ones it don't walk around anymore and works smooth and quiet now. I also have to add that Parts Select has been absolutely GREAT had the parts, delivered when promised.

So easy and convenient!!!

Removed the burnt out old one an put in the new.

With a Phillip head screw driver

Replaced pump assembly

It took me a minute to put the baffle in place. The piece got here in one day. I would order again from here if I ever need any parts for any of my appliances. Thanks Anne B.

Plastic door hook was broken in half and door lock (DL) error code was showing-- though the hook was still in the door (each half held in by its own screw) and the door actually felt as if it was still latching o.k. After reading some things online, I though it was worth buying new hook since it was cheap, and giving it a try. Got it for a total of about $11.00 a little over 48 hours after placing order. It took about a minute to put it in. Then, tried to start the washer and "Voila"-- same error code still appeared! Read some more stuff online and saw a recommendation for "restting" this error by unplugging and replugging the pink wire harnesses at the back left of the top of the machine, after taking off the top (held on by just 3 screws at the back edge). So I did this (after first unplugging power cord), and this time "Voila", it worked! So I assume the error code was initially caused by the broken plastic hook, but the code stayed in the system (even though I had also tried unplugging the power earlier)- and then was cleared off when I did wired harness unplug/replug operation. So the situation was a little puzzling, but still an "easy fix" overall.

I just took the old door handle and put the new one on with just 2 screws. Very easy.

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

Remove two screws and replace.

Very easy to install and was very easy to find the right part on the website. Bookmarked this site in case I need any appliance parts.

It was an easy fix,all I had to do was pull the washing machine out and remove the top off the washer,leaving everything connected,I cycled the machine to figure out where the leak was in the first place,then unpluged the washer,turned off the water and removed the water lines from the back of the washer(be sure to have a couple towels handy)disconnected the 4 color coded wires from the inlet valve making note of which color went to which relay,disconnected the hose from the inlet valve,and removed the one screw holding he valve to washer.That was all,then reversed the procedure to put it all back together. success! took about 20 min start to finish.

Unplug washer. Open door. Look at the very bottom of the bellow and will see a spring that is connected to a small wire that runs around the bellow holding the outside on. Using a flat head screw driver insert it between the wire and bellow, pull down slighty. Grab the wire and gentley pull off. Now the outer part of the bellow will be free, pull it toward you, and off the water/soap despinser, then push it into the washer. Now look to the right side and you will see a screw head that is actully a big clamp ring around the bellow. This is the hardest part. Use a small rachet screw driver with a 7mm socket to lossen. Pull clamp off gently, you can now removwe the bellow. Put bellow back on in reverse. There will be a small tab on the bellow it goes to the top. Took about 2 hours.

This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.