GHD4309L15BB General Electric Dishwasher - Instructions

In order to access the fill valve, dishwasher had to be removed from under countertop. Disconnected water supply line and drain hose under sink. Unplugged unit and removed 2 screws holding unit to countertop. I was then able to pull unit out and replace valve. After reinstallation, the same problem existed. Further research pointed to the control module, approx. $100.00 or the motor, approx. $250.00 - $300.00. I than began looking at new dishwashers, but I did email GE with the problem. They suggested I use citric acid or vinegar in hot water, pour into right rear portion of tub and wait 1/2 hour. After doing that, the dishwasher worked perfectly.

I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Traced the problem back to the water valve. turned off the water. Disconnected the water inlet and outlet lines. removed the 2 mounting screws and unplugged the terminals.

Dishwasher would not drain. I confirmed it was the drain pump by starting the DW and pressing reset 10 sec. later. When functioning properly, pump will engage and drain the DW. In my case, nothing except a blinking light for 30 sec. I turned off power at circuit breaker, remove base plate (no need to pull dishwasher), disconnected pump from hose (DW side) and caught water, disconnected hanger hook from DW (requires a little twisting), disconnected on house drain side, marked two sets of wires (1,2), removed wires by shoving nail into coupler (otherwise hard to disconnect), and removed pump. Repeat in reverse order to connect new pump.

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled

My dishwasher was doing a terrible job of cleaning. It was leaving food on dishes, and wasn't dissolving all the detergent. I replaced all the spray arms and the filter, as they seemed clogged, and god knows how old. It's a super easy repair, and the dishwasher now works as if it were brand new.

First, I pulled out the drain hose under my sink that connected the dishwasher to the disposal and overflow valve. I drained all the water out of the dishwasher and ran it to see if it would drain. It did not. So I drained the water out again and then pushed the hose back in the hole it came through from the dishwasher. My water for the dishwasher is hooked up under my sink as well so I pushed the excess length of hose through the same hole to give me enough play to get the dishwasher out. Other people may need to disconnect the water first, but regardless, turn off the water at source under the sink.
After concluding that the drain pump was running at the end of the wash cycle (I could hear a slight buzzing sound), I figured that the timer was working as it was telling the pump to run and determined that the pump was not working properly.
I unscrewed the screws that held my kick plate on below the dishwasher door. Turned off power. Took a digital pic of the wiring so I could refer to it when putting back in. Unhooked 3 wires that supplied power.
Then I unscrewed the screws that held my dishwasher under the countertop (2 small screws).
I gently pulled out the dishwasher until it was free of the space it was in under the counter. I put two 3ft 2x4's on the kitchen floor with a few towels under to soak up the extra water that was unable to drain ealier. I turned the dishwasher on its side so that the bottom was now visible.
I then took a digital pic of the broken drain pump all hooked up so I could refer to it when putting the replacement in. After removing the two wires hooked up to the pump and loosening both sides of the pump from the drain and drain hose, I removed the broken pump.
From that point, I installed the new pump and tightened both ends securely, hooked up the wires, picked up the dishwasher on it's bottom, hooked up the three wires for power supply and gently put dishwasher back under counter. I had to pull the drain hose gently and water hose so they would not kink behind the dishwasher. I hooked up the drain hose to the disposal and overflow valve, turned on the water and the power and ran a test cycle. Good to go!

I removed the screws on the inside of the door assembly, which allows the inside of the door to seperate from the outside. The escuchen (control panel) was easy to remove - the handle actuator is inside the control panel. The handle assembly was easy to take apart and re-assemble with the new handle and spring. I then inserted the control panel back into the outside door and reattached all of the screws with a power drill. This was a repair that a GE-authorized service tech told me was going to be over $540 - he claimed the control panel and door handle/actuator was a single assembly. In the end this repair cost me $14 in parts and 15 minutes of time. I complained to GE Consumer Affairs and they rebated the tech house call back to me in 5 business days.

Exchange the old rack with a new one

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

Ordered your new and improved interlock cover made with better plastic (thank you). Your new spring is also better. It's bigger and longer and is now the right size. (Thank you). Your parts are better than oem. The interlock is easy to get to. The oem one is black and you can see that it is bulged. The replacement one is gray speckled with white and black. You can see the improvement by just making a comparison. Just unclip the old one and clip in the new one. . Repace panel cover. Now it works and should work now for many a year. Thanks! Parts select.