Models > GFWR4805F0RR > Instructions

GFWR4805F0RR General Electric Washer - Instructions

All Instructions for the GFWR4805F0RR
1 - 8 of 8
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drain pump failed
Remove back cover and with a light and a mirror the screws can be identified. Three hold this pump on. Remove electrical connection then the pump. So also remove the corrugated connecting boot by undoing three clamps. Clean and reassemble
Parts Used:
PUMP DRAIN
  • John from LYONS, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Riper gasket main, needed replaced.
After trying multiple times, multiple ways to stretch the gasket over the washer drum with no luck, I was able to get it installed but it took 2 more people. 4 hands to hold the gasket while the other person fits it around the drum. I noticed in the install videos they start the process then cut away, and magically the gasket is installed.
Parts Used:
GASKET MAIN
  • Michael from WELDON, IL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was vibrating during spin cycle
Problem got worse the technician installed the damper assembly but the problem got worse . The machine sounds like a tractor .
Parts Used:
DAMPER ASSEMBLY
  • Linda from Miami, FL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    1- 2 hours
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Power spike caused the control not activate motor on drum.
I downloaded a service manual for $9.95 online that lead me step by step to the board.I order the board from another supplier but it was back ordered for 4 to 6 weeks. Was lucky to find Partselect. They had the part in stock with fast shipping.
Parts Used:
Electronic Control Board
  • James from CONCORD TWP, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leakage, inner basket bearing play, motor not running
Replaced outer drum, both halves, inner basket/trunnion assy. , Fan housing from excessive vibration/broken mount tabs. Used multimeter to test rotor position sensor ohms, replaced sensor, machine operating as new now.
Parts Used:
BASKET AND TRUNNION Assembly
  • Rodney from NEW BALTIMORE, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Socket set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace basket or drum and bearings and seal on a front load washer
removed the tub and drum assy. replaced the bearings and seal put back a new drum. and put it back together.
Parts Used:
SEAL O-Ring GASKET MAIN CLAMP GASKET BASKET AND TRUNNION Assembly HOUSING FAN ONR
  • Blaine from BRIGHAM CITY, UT
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Power surge. No display
Replaced smoked Electronic Control Board, powered up and ran diagnostics. Machine powered up just fine but would fail the drum speed test. Replaced the RPS Module and machine works like new
Parts Used:
Electronic Control Board
  • Tom from OWASSO, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
TUB OUT OF BALANCE
Replaced the balance ring on the tub but the main tub was cracked and could not be repaired.
Parts select was very helpful. Sent me instructions to repair the washer and replaced defective parts from shipping within 2 days. VERY GOOD EXPERIENCE
Parts Used:
RING BALANCE Assembly
  • Regis from SAN MARTIN, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GFWR4805F0RR
1 - 8 of 8
Back to Top