GFS2271L10 Caloric Refrigerator - Instructions

following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Followed on line instructions. Instructions were very helpful. The part was an exact replacement. Everything went as planned.

Followed the Video, and it went almost as the video, except for the rails for the ice tub, so instead of the nut driver, had to use an open end 1/4" wrench. Now its a working with lots a ice....

I received the new icemaker the next day after I had ordered it. After watching the video on how to install the icemaker I installed it within a few minutes which I really surprised myself since this was my first repair job to do by myself. The new ice maker has been working great and I am very pleased with partselect and will continue to contact you when I am in need of any parts. Thank you, betty

1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.

Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

The ice maker was easily replaced, however I still had no ice. I ended up using an on-line repair service which determined that the problem was the water inlet valve. Replacing it was beyond my expertise so I hired an appliance repairman.

just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time

After reading the articles previous owners wrote, I tackled the repair. There were no big problems until I had to change out the water line on the icemaker tray--that part was for a different frig--so it had to be changed out with the Amana water line part that was enclosed. I couldn't get that part removed, so I had to have my husband change it out. He then finished the installation. Everything went smoothly, just my pride wanted me to finish it all by myself.

got the model number off the fridge. ordered the part. received the part. the funnel part that drains the water into the tray was broke when I received the new icemaker, I took the one that was on my old leaking icemaker an put it on my new one along with the old hardware parts {wireharness, ice level bar}. followed the video instructions an wahlah nomore ice in the bottom of the freezer or in the floor. it looked like the funnel was broke in shipping. its great to have ice because its fixing to get hot!