GFE461LVQ0 Whirlpool Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

My husband had no problem at all with the replacement of the exterior glass.
Slipped it in and attached to hooks and secured with the handle with a screw driver. Be sure to remember the trim doesn't cover the glass it kind of sits behind it. It can be deceiving in a way you may think in sits in front of the glass. Otherwise it was quite easy and the part came quickly in less than 24 hours....this is a great site.

Followed youtube instructions: lifted clips on door hinges, removed door. removed screws, removed rear cover, replaced right hinge. reassembled door. caution: door handle will fall off when top two screws are removed. Alignment of screws is some what difficult, requires awl.
Replace door, return locking clips to forward position, check door for operation.

I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

Simply removed three screws that held the door trim in place. Once the screws are removed be carefull because the front door glass is held in place by the bottom door trim. Otherwise an extremely easy repair.

I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

Took off top and pulled out old element and plugged in the new one

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

Remove vent trim from oven and set oven glass to the side. Next remove handle from vent trim (two screws). Next place handle on new vent trim. Place glass in place, (it is held in place by bottom of oven door and vent trim). next place side trim in place and place that side of the vent trim and loosely tighten screw holding trim into place at top of the glass. Next place the other trim into place under the vent trim and tighten the screws on both sides.

I didn't. Don't know how to get to light bulb to change it for this specific model

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.