GAFZ21XXRK02 Whirlpool Refrigerator - Instructions

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

I replaced the relay started right up did fine for about 4 days. Came home from work I had lost everything in the freezer again.turned down the thermostat and back up and it started right up. 5 days later same thing again.

First I called my friend Robert in Kissimmee, Fl to have an idea regarding the problem because I had never serviced a fridge before. Then he suggested that I check with PartSelect on the Web. Then PartSelect repair videos showed me everything. I followed step-by-step but the problem persisted. I finally realized that the airflow conduit between the freezer and the fridge was clogged with ice. I then proceeded to remove the ice underneath the coil on the aluminum cover and Bingo. The problem was in fact the ice. Well, I only spent $33 dollars for the non-necessary Bimetal Defrost Thermostat. I learned a great deal from that repair.

I replaced broken fridge with a spare fridge; mean while I went online and did research and came across "Parts Select" which was extremely helpful with similiar situation and helpful guidance. $80 and fridge is as good as new.Thank you.

I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

I just removed icemaker, bottom and back panel cover, remove the old thermostat, cut the wires, connect the new one and replace all covers and ice maker.So far is working perfect, no more water mess inside or on the floor, and my food is not frozen anymore, thanks a lot for your help and your trouble shooting help me to figerout what was wrong, thanks again for save me a lot of money

We followed de video that made it very clear to us. Thank you! It's been working great since...

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Had to take everything out and defrost the whole refrigerator dry up and than took back off at bottom and the one covering the Bimetal. The hole was plugged so we took the compressor and blew it and finally got all the ice out before we put on the Bimetal. This is the 4th time we fixed this and I don't know why it won't last longer than 8/9 months. The warrenty is for a year and so far I have gotten 2 refunds thank you!

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.